Hello friends, in this video you will be watching second part of 3 in 1 sanding station. You can find all the measurements at the end of the www.- a. Belt disk sander - 27 products on Joom. If you're looking for high-quality and affordable belt disk sander - you'll find the best belt disk sander at great prices on Joom - from 3 to 8 USD. A wide range of available colours in our catalogue: Red.  If you're not satisfied with the quality of belt disk sander you've received - please contact our support. We'll review the issue and make a decision about a partial or a full refund. ⭐Free worldwide shipping. All products from belt disk sander category are shipped worldwide with no additional fees. Frequently Asked Question. 💡 How to buy belt disk sander? — Choose a product. — Tap a "Buy" option to place the product in the cart and proceed with your order. — Choose a quantity of belt disk sander. (Default — 1. Maximum number — 20). Find great deals on eBay for belt and disk sander. Shop with confidence.  Sp3oYn9soQRZWred. Sander Machine WEN 4 x 36 Inch Belt Disc A Motor Steel Design Industrial Tool. Brand New. out of 5 stars. 16 product ratings - Sander Machine WEN 4 x 36 Inch Belt Disc A Motor Steel Design Industrial Tool. C $ Top Rated Seller. Top Rated Seller. Shop by Disc Diameter. Condition see all. The view of the back 3not often seen in brochures, shows from left to right; a the tracking control knob; b the belt tension lever; c the table mounting arrangement; d the backstop and e the drive belt cover. Photo 23 shows the inside the motor which appears to Warco Belt And Disc Sander Oil be an open frame 2-pole induction motor and the back of the NVR switch. There is quite a lot warco belt and disc sander food free play in this arrangement but it should get to within a couple of degrees.

Not Specified. Type see all. Disc Sander Filter Applied. Action see all. Color see all. Condition see all. Open box. For parts or not working. Please provide a valid price range. Buying Format see all. All Listings. Best Offer. Buy It Now. Classified Ads. Item Location see all. US Only. North America. Delivery Options see all. Free International Shipping. Show only see all. Returns Accepted. Completed Items.

Sold Items. Authorized Seller. Authenticity Guarantee. More refinements More refinements The table is only bolted to one side of the belt platten and this means there is some flex if you press down on the table. The protractor is fited onto a length of aluminium 'U' extrusion which slides in the slot machined in the table. There is quite a lot of free play in this arrangement but it should get to within a couple of degrees.

It is possible to fit both tables to the belt platen at the same time, this may be useful in some circumstances although I am not sure for what. To remove the belt the platen has to be in the raised position so that the belt will clear the support foot and the top of the disc housing 8.

The belt tension lever has Warco Belt And Disc Sander 65 to be released and the belt can then be slid off towards the front. Replacing the belt is straightforward the only thing to note is the direction of rotation which is marked on the inside of the belt 9. Apparently the belt join can come apart if the belt is fitted the wrong way round.

Once the belt is off the construction of the platen can be seen 10 , a steel pressing with a couple of reinforcing cross pieces riveted in. I did note that the pressing process has left the top of the platen bowed upwards slightly, probably about 0.

Despite being a fairly hefty pressing the platen still has a certain amount of torsional flex but I doubt if this would be apparent in use. The tension roller at the right hand end of the platen both applies tension to the belt and adjusts the belt tracking.

The mechanism is quite simple and a clever design but could be better made. The roller has ball bearings quite deeply inset from the ends and a 10mm support shaft, the shaft is machined with a flat on one end to stop it spinning.

The shaft is mounted in a 'U' shaped bracket which in turn is restrained in a slot on the underside of the platen The whole bracket and roller assembly can slide both along the table and to a lesser extent from side to side. In use this bracket is forced out by a fairly hefty spring to provide the belt tension. The operating lever is an over centre design which is either completely loose to change the belt or in tension when in use. The roller bracket pivots and slides about a short column fitted to the underside of the platen with Warco Belt And Disc Sander 60 a bolt that goes through the platen and is held in place by a nut and washer.

The washer in the photo is one I have fitted. A screw adjuster pushes the bracket from side to side and a compression spring holds it in place this serves to adjust the belt tracking.

Note that the roller assembly is closer to one side, there is about 10mm at the rear and 15mm at the front, this I believe is the cause on a number of problems I encountered before getting the unit to run. I encountered a few problems with the machine but these were easily rectified and I soon had the sander up and running smoothly. Before running the sander I pushed the belt round by hand, this caused some very strange rubbing grinding noises from within, I removed the belt and made further investigation.

The first thing I found was a a small moulding flash on the plastic housing round the disc. As can be seen in photo 12 the disc is pretty close to the right hand side of both the casting and the plastic moulding. Just above the screw the plastic was rubbing on the disc. I took the disc off and a fine file quickly removed the offending plastic.

The plastic moulding is actually part of the dust extract ducting, the screws hold a plate over the lower part of the disc. A more serious problem was that the tension roller was rubbing on the 'U' shaped support bracket. I removed the roller and bracket assembly 13 and the first thing I noticed was a hefty dent in the edge of the roller. The roller and spindle came out of the bracket quite easily.

A bit of brute force with the vice, a large hammer and a bit of wood got the bracket back into the shape I thought it ought to be i. With the bracket straightened out I refitted the roller and spindle This has got to be the most peculiar bit of engineering! Each end of the spindle has a circlip fitted which prevents any lateral movement of the spindle.

To prevent the spindle falling out of the bracket slot two screws and washers 15 clamp the circlip to the bracket - weird. I refitted the roller and bracket assembly and had considerable difficulty getting the spring 16 in place around the tracking control screw. As can be seen from the photo the spring is fairly long and quite thick about 35mm long x 12mm diameter. Basically the spring was too big and fully compressed about 12mm long would not let the roller move far enough to the back.

I am guessing here but I think this might have been found either during original assembly or at 'checking' and rather than fix it properly a pry bar or large screwdriver was applied to force the roller assembly into place. Thus accounting for the bent bracket and the hefty ding on the roller. I found a slightly lighter shorter spring and fitted this 17 as can be seen there is still enough space between the spring turns to allow the roller assembly to move into place.

I also fitted some new unbent washers! On with the bent washer saga! I took the belt guard cover off just for interest, the toothed belt and pulleys simply transfer the drive at from the motor spindle to the belt drive roller. The belt guard also serves as the support for the whole of the belt assembly and is a fairly substantial casting. The belt guard is fitted to the main body by three large pan head screws which pass through slots in the casting allowing it to slide up and down to set the belt tension.

The pulleys are a good fit on their shafts which have substantial flats to provide the drive. They are unfortunately held in place by, you guessed it, a bent washer 18 in fact two bent washers. I made a couple of 3mm thick washers with a deep countersink and refitted the pulleys with M5 countersunk allen screws The photo also shows a hole just below the belt guard, this apparently is the belt tensioning device.

You stick a screwdriver in the hole and lever up against the little nib cast into the cover to slide it up and then tighten the three fixing screws.

Build A Toy Motor Quad Diy Shaker Cabinet Doors Kreg Jig Uk