I took the yellow paint, and diluted it with some water on a disposable plate, that way it was thinner and easier for the wood to cilorado through. After a while I worked with a hammer to separate the wood pieces, and a couple hours later the pallet was finally apart! If desired, lightly sand the front side of your flag before painting. Well, time went by and other projects were in the way and I never made it in a timely manner, diy colorado flag wood soon enough it was a month before he was getting married so I thought, well, this would be a perfect wedding gift for them! Forrest and I invited my mom, dad, and brother to come along, which made it even more fun! Diy colorado flag wood this point you can either leave it as is or seal it with some polycrylic.

We did that a few times, mainly after we finished eating at one of the many yummy restaurants there. Since my little brother was getting ready to leave to go to BYU in Utah, he wanted to try and find something to put in his dorm room to show is Colorado pride!

Unfortunately, we had a hard time finding anything beyond t-shirts. This is a great going away present for college students, or for someone who just loves the state! Forrest and I spent a lot of time picking out the right shades of colors for the flag when we were at the store, so the exact brand and colors I list below are what we recommend!

Something to attach to the back so it can hang on the wall — we chose to use wooden rods, but if your wood is thick enough, you can probably get away with a hammer-on picture hanger! Paint two boards blue and one board white. Let them dry completely and then paint with another coat. You may want to do an additional coat after that just for good measure. Using wood glue, glue the three pieces of wood together. Lightly rub the cloth onto the taped of section of your flag, using long light strokes.

You can always add more color in layers for a bolder look. Make sure not to cross the tape line into other colored sections. Keep your cloth wet to ensure even distribution of color. Once paint is dry to the touch, remove the tape Diy Wood Burning Projects Quiz and repeat this process with each colored section of the board, painting the darkest colors last. When the last section is done, use a Q-tip lightly dipped in water and paint to touch up any colors that might have bled from one section to another.

Small bleed areas on the red paint line that are not noticeable from afar. Acrylic paint dries quickly, so you should be able to hang this wood state flag masterpiece within an hour after finishing the last section. Can you tell me what you used specifically. I love how yours looks! Dress up your home by creating DIY wall decor inspired by your very own state. I chose to use 7 pieces of wood for the flag.

Next comes the sanding process! Sanding is fun, but it sure gets dusty!! I then laid out the wood in the placement I wanted. Some of the pieces were darker than others so I wanted to break them up so it had a more fluid look. Once I figured out the layout, I flipped over the pieces so I could screw in the structural pieces to the back of the wood.

Does that make any sense?! Screw in two screws per board to help with support. The picture I have below shows 1 screw for each piece. And voila! Since I was doing the Colorado state flag, I wanted to make sure the circles I was going to draw were damn near perfect as I could get.

Once finalized on the design, I used the compass for the markings on the wood. In between this Diy Wood Us Flag I took a damp cloth to wipe down the wood to take off excess dust and dirt so the painting job will be clean. OK…NOW for the coloring! I love Target! I started with the yellow inner circle. I took the yellow paint, and diluted it with some water on a disposable plate, that way it was thinner and easier for the wood to show through. Just kind of work with it!

I would end up dipping my paint brush or poly brush in water every time I would paint to help the process too. Once painted, I then would take a paper towel, fold it up and wipe off the excess paint so it gave that washed wood effect.

Do It Yourself Garden Tool Storage Zero Small Lathe Machine For Wood Registration Joinery Tools For Sale 5g