Choose a few times that work best for you: 1. Delivery From Your Drawer slide mounting brackets youtube Ace. I wish they would do better about keeping the drawers in stock. Head off scratches with a light polish. Miguel Zepeda 13 Nov Reply. Slide it back to reveal a screw slot and drive a screw. Printer-friendly version.

By loosening the mounting point, you can slide the hinge in the slot to gain adjustability. This gives you more room for error than when working with wood. European hinges require a pocket in the door to accommodate the hinge mechanism. Use a 35 mm hinge forester bit to create the required pocket.

You would still have to do this even if your cabinets were framed with wood. You will need these hinges and mounting plates to make it all work. The large overlay is what covers up the aluminum framing. It takes a special hinge to do that. Drawer slides may require that you run a lateral bar of extruded aluminum behind it to offer a mounting point. Much like the cabinet hinges, a threaded t-nut provides the thread in the extrusion.

Then you simply align the holes in your drawer slide and pass the bolt through the hole and into the t-nut. The Blum drawer slides used on the Karavan come with a number of pre-drilled holes that simplify installation. Look closely at the photo below. Three M4 bolts pass through holes in the drawer slide and into M4 t-nuts in the framing. There is a fourth bolt further back that is hidden by part of the drawer slide.

Four bolts is overkill, three would have been fine. I found it necessary to use low profile bolts here as my Blum drawer slides had tight tolerances. Another aspect to consider is the need for positive latches to keep cabinet doors and drawers closed when driving.

We used stainless steel marine latches on our cabinetry, which requires mounting a catch for the latch to grab on to. This meant we needed to add laterals across the front of our galley kitchen framing to hold the latch catch. Like the hinges, we drilled holes in the catches and bolted them to the framing via roll-in t-nuts. Unlike the drawers, the overhead cabinets require no additional framing for mounting the catch. The lower support member is a perfect location for the catch. Another common piece of hardware used in vans are lift struts to hold overhead cabinet doors in the open position.

We again used Blum lift struts , as they offer a screw-adjustment for fine-tuning of the lift mechanism. See our Store for all associated parts. Set too high and the spring tension will want to lift the door so hard and fast it will almost pull the door out of your hand.

Mounting the lift struts required an attachment to both the wooden door as well as the aluminum framing. Use the provided wood screws to attach the lift arm to the door.

Now we need to attach the lift mechanism to our framing. Just like the hinges, we drilled a new hole in the mounting bracket to align with the slots in the aluminum.

Only one hole and bolt was required to mount the lift strut. Flexibility, people. We like the look of hex cap screws. We offer all of our write-ups and instructional videos for free.

A lot of time, effort and money goes into developing and maintaining this website. If you find the information on this website helpful, you may use our various links when you are ready to make purchases. As Amazon Associates we will make earnings from qualifying purchases, however it costs you nothing to use them. Alternatively you may consider using the donate button below to make a simple Paypal payment, or message us if you prefer Venmo. We sincerely appreciate your visit as well as your support.

The aluminum framing makes it really easy to attach cabinet hardware. Instead of drilling a wood box and inserting wood screws, you drill the hardware brackets and bolt it to the framing using t-nuts.

These connections can be loosened and tightened repeatedly without losing strength like a wood screw in a wood panel. In a separate article we will discuss how to build drawers and cabinet doors. Thank you for sharing the van building adventure! My question is about the lateral bars to support the drawer slides. On;y because I intend to inset my side panels into the extrusion. With a drawer bank towards the corner, the lateral bars would not work for me. Best of luck! The drawer dividers that the locking drawer latch catches on also helps support the front of the drawer slide, so that helps too.

Hi Ken, Let me begin by saying what a pro you are. You put other DIY van builders — and van v-bloggers — in the dust. Thank you for being so generous in your information, and so thorough in the information you share. Did you do the uppers yourself? Am I missing a video, or…? Any sketchup plans you could possibly share.

Hi Gano, thank you so much for the kind words. I sent you a message privately…really appreciate the support. From the headliner to the outside of the framing they are about You can reference the video for the factory holes I used for mounting and come up with the same result. If you need specific measurements let me know and I can come up with them. I drill through my panels and into the Then I tap threads directly into the to secure my panels.

It is plenty solid and saves the time of aligning the panel and the tnut on a vertical panel. My question is how do you secure the mounting plates so that you can drill new holes in them? Thanks, in advance. A regular t-nut of course would just fall down under gravity. Ball-bearing slides. Why choose these? Ideal for drawers with hefty contents, such as silverware or tools. Full-extension range allows the drawer to open fully for best access to contents in the back.

Installation is the same for each style. Lubricated bearings make for the smoothest sliding action. Additional features, such as self-closing mechanisms or higher weight ratings, increase this cost. Mount to the drawer first 1. Facebook Pinterest Twitter Text. Printer-friendly version. Read more about Fasteners and Hardware or Doors and Drawers. How To Mortise Box Hinges. How to install metal slides on wood cabinets. European bottom mount drawer slides are easy to install and are ideal for storing your personal items with loads up to a 50 lb.

Consult our bottom mount drawer slide installation instructions. Use Side mount drawer slides in your next home drawer installation project. Consult our side mount drawer slide installation instructions. This drawer slide has a 35 lb. Consult our center mount drawer slide installation instructions. From drawer slides, cabinets and furniture to bathroom, kitchen and dining room solutions — let us help inspire your next home project! Style Casual.

Utility Whimsical.

Belt And Disc Sander Ebay Jobs Large Wooden Mallet Hammer Jacket