Ikea stopped offering 1. See our Woodworking Eatin area for more information. Do you have this? Your butcher block will look amazing. So satisfying. Proper testing of the entire process should be completed before beginning.

This is especially important when applying the ORIGINAL Satin Finish as this will provide enough wet film thickness needed for the pigment in the finish to re-align itself before it dries. The proper spread rate will also allow enough time for the product to properly flow and level. Remedy for a larger project such as a floor.

We recommend buffing the entire surface with a worn maroon pad, tacking the floor with a lint-free cloth dampened with regular mineral spirits paint thinner and re-coating the surface properly. Try to feather in your start and stops and use smooth and even strokes to float the applicator with the finish over the surface, versus pushing down hard on the applicator. Another choice would be to leave the project alone as the imperfections may fade after the finish has had time Waterlox Original Sealer And Finish Uk to cure.

Remedy for a smaller project such as a table or counter top. If you have to re-use a container wipe it out thoroughly with a dry cloth when you are done with a coat.

If you allow the Waterlox to dry in the container, and then try to re-use the container, you are pretty much guaranteed to get glops of dried Waterlox in the next coat. The quart-sized Waterlox Original Sealer comes in a rectangular can. Crinkle up the can as you go. This pushes air out of the can which would otherwise dry out the product. Well, wrong. Pour the Waterlox out of the can in the way shown in this photo but take the cap off, of course to keep the stuff from pooling on the top of the can, making the screw cap harder and harder to twist off as the layers of Waterlox dry in the cap grooves.

As they state on their website, Waterlox penetrates deep into the wood. It has a consistency closer to water than to, say, polyurethane. I suppose this depends on the wood you are Waterloxing but for both the Ikea and Menards butcher block I worked with the stuff really soaked in. I lay my second coat on thick too. After this coat dries you will need to sand. Sanding between coats from here on out is absolutely the key to getting a super smooth finish.

I sand with grit paper , then wipe the entire surface down with a clean damp rag and then I wipe everything down again with a clean dry rag. I look for dull areas going into a new coat. Waterlox will self-level if you put enough on. I find that you have to work a little quicker with the Satin Finish. It just seems to set a little quicker. Definitely do not touch up as you go see Tip 8. That final coat is so satisfying to put down and when it dries it has a gorgeous feel to it.

Your butcher block will look amazing. Okay so this tip is about purchasing butcher block, not applying Waterlox. Ikea stopped offering 1. Also, did you know that you can get butcher block through Amazon? Now you do! Have you used Waterlox on butcher block?

Love it? Hate it? Please share your experience in the comments! My husband and I have researched how to refinish our maple island top and you wrapped it up for us in detail. Thanks again! Thanks for your comment Charolette! I hope your maple island top turned out great! Hi Sara — thanks for visiting and for the great question!

Hope that helps! Can i just seal the sink well and not worry what the inner walls where the sink cutout is? Or will i need to cut up the caulking, pull the sink out, and seal the inside cutout? Hi Nathan — First off apologies for the delay in this reply.

Seems we are back now which is great. If the sink in question is in a rental unit, I might re-do it, coat the cut-out, have peace of mind.

Thanks for the specifics. I made my list and will refer to this! Now to see if Ace carries Waterlox. I am considering staining it first since I like either lighter wood or darker and not as crazy about the medium shade. Hi Alicia — thanks for writing! I have only ever seen Waterlox online. I think Amazon was able to get it to me a little quicker and with Prime I got free shipping. The color will change a little with the first coat of Waterlox, and then deepen with time.

Your project sounds great and I hope my tips help to make it go smoothly. Good luck! Fantastic details! Thank you for your tips on how to apply Waterlox. Getting ready to put my Satin Waterlox last coat on now. I also appreciate the post on how the countertops have held up and cleaners to use. Thanks for taking The time to post and help the rest of us DIYers!!! Thanks so much for the comment Kirstin.

So glad this post helped you crush this DIY project! So satisfying. Using the right cleaning products is truly key. Enjoy your countertop! Hi Nathan — thanks for your question. Will check it out! Thanks for the info! I have had 5 coats of Waterlox on my butcher block counters for two years. I have a problem with any stickers on the counter or even magazines sitting on it for more Waterlox Original Satin Finish Quart Nova than 1 minute. When I go to pick up the sticker or magazine, it is firmly stuck to the counter, and I have to soak and scrape it with a credit card.

In some cases, the finish has peeled up all of the layers leaving a big, highly noticeable spot. Do you have this? How can you stop or fix it? Hi Eric — I have not encountered this problem to the extent that you describe.

I have experienced a very stepped back version of ink-transfer with glossy magazine covers. But a few spritzes of a natural cleaner, let it set for a minute, and then a wipe up with a paper towel has taken care of things for me.

A couple quick passes will do. Remember that the purpose of sanding is to remove scratches from the wood surface to give the wood a nice appearance. The finish is what creates a smooth surface rather than heavy sanding.

Step 2 After sanding it is very important to remove every speck of dust on the woods surface. First use a vacuum to pick up all the dust and then use a lint free cloth with a little mineral spirits on it to remove any remaining dust particles.

Allow the mineral spirits to evaporate off the wood completely. Next wash your hands to free them of any oils then wipe the surface of the wood off with your bare hands to remove any remaining dust or lint particles. Step 1 Pour some Waterlox into a clean glass container. Run the tip of the foam brush over the edge of the glass container to remove a small amount of Waterlox to prevent drips.

Step2 Brush the Waterlox onto the wood surface following the grain of the wood. You will notice that the wood almost soaks up all the Waterlox in a short period of time. Allow this coat to dry under perfect conditions for twelve hours. There is no need to worry if you see small bubbles in the finish. Cross ventilation will significantly speed up the drying process. Step 3 After you have allowed the Waterlox to thoroughly dry apply another coat of Waterlox Original in the same manner you did in step 2.

Allow to dry thoroughly for at least 12 hours or more if needed. Step 4 Lightly sand the wood surface that you applied the Waterlox on with grit sandpaper. Two or three firm passes will do. You will notice white dust appear as you sand. Wipe away any dust in perpetration for the next coat of Waterlox.

Step 5 Apply another coat of Waterlox and allow it to thoroughly dry as you did in step 2. This will be the 3rd coat. Step 6 After the 3rd coat has dried you will want to sand lightly with grit sandpaper and then grit sandpaper.

Radial Arm Saw Recall Kit 300 Pumpkin Carving Kitty Ideas Kreg Pocket Holes On Mitered Corners Go Baby Lock For Kitchen Cabinets Quora