Red Oak Plywood | Hardwood Plywood | Cherokee Wood Products

Although face thickness may vary, the paper back thickness is consistent. Also referred to as wood on wood. Bird's Eye Due to local sharp depressions in the annual rings, accompanied by considerable fiber distortions.

Once the depressions are formed, succeeding growth rings follow the thick veneer oak plywood quote contour for many years.

Rotary veneer cuts the depressions crosswise, and shows a series of circlets called bird's eyes. Thick veneer oak plywood quote occurs only in a small percentage of Maple trees.

Bee's Wing Small thick veneer oak plywood quote tight mottled figure similar in appearance to a bee's thick veneer oak plywood quote. Occurs mostly in East Indian Satinwood, also occasionally in mahogany and Thick Veneer Walnut Plywood Year eucalyptus. Blister Produced by an uneven contour of the annual rings. The veneer has the effect of being blistered. Must be cut rotary or half-round.

Block Mottle An irregular variation in the cellular structure of the wood which shows as blocky patches across thick veneer oak plywood quote grain of the veneer. It is commonly found in makore and anigre. Book Matching Achieved when successive veneer leaves in a flitch are turned over like the pages in a book and are glued in this manner.

Since the reverse side of one leaf is a mirror image of the succeeding leaf, the result is a series pairs. Individual panels can be matched this way or you can achieve this look over many panels by sequence-matching the panels.

Thick veneer oak plywood quote matching is the most common match. A common problem in book matching is when the "tight" Thick Veneer Oak Plywood and "loose" sides are matched and reflect light and stains differently. This may yield color variations in some species which may be minimized by thick veneer oak plywood quote finishing techniques.

Bubble Free Veneer A veneer Thick Veneer Oak Plywood Up face of any species applied to a double paper layer of two 10 mil papers. With moisture resistant thermoset glue, the overall backer thickness is 22 mils. Burl Veneer Produced from a large, wartlike growth on the trunk of the tree. The grain pattern typically resembles a series of eyes laid thick veneer oak plywood quote by side.

Obviously the veneers leaf sizes are generally small and additionally are defective. While producing beautiful patterns, burl veneer is thick veneer oak plywood quote to work with.

Butt Matching Achieved when veneers are matched as described for book matching but the ends of the sheets are also matched. At times, the veneer being used is not long enough to cover the desired panel heights.

In this case the veneer leaves can also be flipped end for end and the ends matched. Button Figure Wood species with large medullary rays are quarter cut to reveal the harder and shiny rays which show up as flakes or buttons on the straight grained background.

Species such as white oak, lacewood and American sycamore are cut this way specifically to reveal this figure. Cathedral A grain appearance characterized by a series of stacked "V" and inverted "V". Pattern common in plain-sliced flat-cut veneer. Center Matching Each panel face is made with an even number of flitch sheets with a center line appearing at Thick Veneer Oak Plywood 45 the midpoint of the panel and an equal number of veneer sheets on each side of the center line.

The number of leaves on the face are always even, but the widths are not necessarily the same. Checks Small slits running parallel to the grain of wood, caused chiefly by strains produced in seasoning.

Core There are four types of core construction used in plywood panels: a Lumber Core: Consists of a heavy core of sawn lumber between crossbands. The thick center core permits doweling, splining and dovetailing. Veneer Core: Method of plywood construction consisting of 3,5,7 or more plies of veneer laid with grain direction of adjacent thick veneer oak plywood quote at right angles to each other.

Particle Board: This type of core consists of chips or flakes of resin-coated wood fused together under heat and pressure to form a core for plywood. Mineral Core: Used for fireproof panel construction. Veneers are bonded to a hard noncombustible material. Cross Fire Figures which extend across the grain as mottle, fiddle-back, raindrop and finger-roll are often called cross figure or cross fire.

A pronounced cross fire adds greatly to the beauty of the veneer. Crossband The veneer sheet between the core and face veneer. Its grain runs at right angles to the grain of adjacent layers, thereby providing the remarkable stability of hardwood plywood.

Crossbar Type of figure or irregularity of grain resembling a dip in the grain running at tight angles, or nearly so, to the width of the veneer.

Crotch Veneer Produced from the portion of the tree just below the point where it forks into two limbs. The grain is twisted, creating a variety of flame figures.

Often resembles a well formed feather. The outside thick veneer oak plywood quote the block produces a swirl figure that changes to thick veneer oak plywood quote crotch flame figure as the cutting approaches the center of the block.

Edgeband Thin strips of veneer used to cover the exposed edges of panel substrates. This veneer is usually available in rolls of various length and comes either pre-glued or unglued.

Some burls and figured woods might also fall into this category. Face The better side of any plywood panel in which the outer plies are of different veneer grades. Also veneer spliced to a certain pattern and cut to exact size.

Fiddle Back A fine, strong, even, ripple figure as frequently seen on the backs of violins. It is found principally in Mahogany and Maple; cut occurs sometimes in other woods. Figure The pattern produced in a wood surface by annual growth rings, rays, knots, deviations from natural grain such as interlocked and wavy grain, and irregular coloration.

Appears across the grain. Mottle, fiddleback and raindrop are often called cross figure or cross fire. Flake Fleck Figure Flake figure is developed only in those species which have very heavy medullary ray growth, specifically Oak, Lacewood, and Sycamore.

When the saw or knife cut is directly on or near to the radial, it is close to parallel with the medullary ray and therefore develops the "Flake" effect.

Flat Cut Also called Plain Slicingit is the most common method of veneer manufacturing, producing a grain pattern known as cathedral. Because each leaf in the flitch is similar, a consistent and even matching pattern is possible. Flat cut veneer is ideally suited for wall panels and furniture. Flexible Veneer Wood veneer which is joined, processed, sanded and backed with paper or other material to create a fully ready to use dimensional sheet of real wood veneer.

Flitch A Section of a log made ready thick veneer oak plywood quote cutting into veneers. After cutting, all bundles are laid together in sequence as they were sliced. Grading Classifying veneers according to quality standards for each species. This greatly impacts the price and end use of the veneer. Grain Size and arrangement of the cells and pores of the living tree.

Grain is not synonymous with figure. Woods fall into three groups: Fine grained Birch, Cherry, Maple, etc. Coarser grained woods can usually be cut to develop a more conspicuous pattern. Gum Patches or black spots occurring primarily in American Cherry. This undesirable characteristic is acceptable in varying degree in most grades of Cherry. Half Round Slicing Similar to rotary peeling, also producing a high veneer yield.

Used primarily to add width to narrow stocks by increasing the plane of cut. Also used to enhance a particularly wild grain pattern. Matching is possible because the leaves can be kept in sequence. Half round cutting may be used to achieve "flat cut" veneer appearance. Hardwood General term used to designate lumber or veneer produced from broad-leafed or deciduous trees in contrast to softwood, which is produced from evergreens or coniferous trees.

Heartwood Thick veneer oak plywood quote non-active center of a tree generally distinguishable from the outer portion sapwood by its darker color. Herringbone Veneer strips are used and matched to both sides of the center line, at an angle. The resulting appearance is reminiscent of the bones of a fish as they are attached to the back bone. Holes, Worm Holes resulting from infestation of worms. Joint The line between the edges or ends of two adjacent sheets of veneer or strips of lumber in the same plane.

Inconspicuous or blending pin knots are barely detectable at a distance of 6' to 8', do not seriously detract from the overall appearance thick veneer oak plywood quote the panel, and are permitted in all grades. Knots, Open Opening produced when a portion of the wood substance of a knot has dropped out, or where cross checks have occurred to produce an opening.

Knots Sound or Tight Knots that are solid across their face and fixed by growth to retain their place. Lamination The process of gluing or bonding thick veneer oak plywood quote component sections of the plywood into a single permanent until stronger than the original wood itself. Looseside In knife-cut veneer, that side of the sheet that was in contact with the knife as the sheet was being cut.

The bending of the wood at the knife edge causes cutting checks. Generally considered the best substrate for laminating veneers. Mineral Streak A dark patch or discoloration in the wood which occurs because of the presence of minerals in the soil in which the tree is growing. Mottle Figure A variegated pattern which consists principally of irregular, wavy fibers extending for short distances across the face. If there is also some irregular cross figure in a log with a twisted interwoven grain, the broken stripe figure becomes a mottle.

Particleboard A panel composed of small particles of wood and wood fiber that are bonded together with synthetic resin adhesives in the presence of heat and pressure.

Peanut Shell Thick veneer oak plywood quote A type of figure occurring in some woods similar to quilted or blistered figure.

For some popular wood species, like red oak veneer, white oak veneer, walnut veneer, and Burma teak veneer. We can slice to micro thin mm to mm veneer sheets. Chinese local veneered panels manufacturers use moist raw veneers to face the plywood or MDF for furniture and wall decoration. We carry 1/8, and 1/16 hardwood that works great for veneers. Our "Project Ready Wood" comes in 4", 6", 7", 8", 10" and 12" widths and thickness from 1/16, and 1/8 to 3/4 of an inch. 20 Hardwood species to choose from including Walnut, Cherry and Hard Maple. All top grade veneer - no knots or defects. Raw unspliced veneer. 3/4″ Veneer Core Plywood (A Face – A1 Back) 3/4″ thick Veneer Core Plywood is an “A” Face Grade wood veneer with a veneer core and a #1 backing. “A” Face Grade Wood is suitable for center panel material while the #1 backing is suitable for the back side of a cabinet door center panel. This versatile product can be used for many areas of a cabinet including undersides, sides, backs, and fronts, along .

Jet 14 Bandsaw Resaw Engineering Dust Removal System Te Drs 6 A Case Javascript