The installation zone must be selected evaluating the work space required depending on the dimension of the pieces to be machined,and taking into account that a free space of at least mm must be left around the machine. Sign In OR. Description Part No. Rip Fence Assembly - cont. Page 8: Stand Assembly Once the frame is upright, the record power table saw manual assembly should fall into place. Bandsaw Blade Set Up - Cont.

Page 9 Initial Assembly - cont. Unscrew the locking nuts from the mitre fence Fig 3. Place the protractor with the flat edge running parallel to the mitre fence. Fence Screws 3. Position it in such a way that the fence screws slot into the holes on the protractor Fig 3. Page 10 3. Position the fence on to the table and lock off by screwing on and tightening the fence lock knob.

See Fig. The machine is heavy. Additional help or a suitable lifting device or support will be required for lifting the machine onto the stand. The stand and wheel kit comes as a self assembly unit Fig. Stand 1. Page 12 4. Page 13 4. On the underside of the operating frame, find the two raised areas on either side.

Mount the two back wheels and secure in place using the nuts and bolts provided Fig. Page 14 4. Page 16 If the machine is to stand idle for a period it is good practice to slacken tension and re-tension when next using. On the BS the simplest way to release and re-tension the blade is to use the cam handle located on the back on the machine. Page 17 Bandsaw Blade Set Up - cont. This machine is not suitable for cutting metals.

The lower bandwheel has two, integral, multi vee form pulleys and the motor shaft has a twin multi vee form pulley. Always wear safety glasses when using woodworking. Always disconnect the power before adjusting any equipment. Failure to observe proper safety. Always remember that a careless fraction of a second is sufficient to inflict severe injury. Table of Contents.

Previous Page. Next Page. Version 2. Do not overreach. Keep proper footing and balance at all times. Secure work. Ensure that your work piece is properly held before starting to cut. Always use a push stick and keep hands clear of the blade.

Never remove the crown guard or riving knife. These are there to protect the user. Page 5: Record Power Guarantee 2. Page 6 It is advisable that before unpacking to have plenty of paper towels or cloths available to clean off the rust preservative.

Contents of the shipment: 1. TSC Table Saw 2. Sliding Table 3. Wheel kit optional accessory 4. Page 8: Saw Unit Assembly 4. We recommend that assistance is sought before trying to lift the larger components.

Page 9 4. Saw Unit Assembly - cont. Note: When assembling this table saw, Do not fully tighten the nuts and bolts until the assembly is complete. Page 10 4. Mount the two back wheels and secure in place using the nuts and bolts provided Fig. Page 11 4. Unfasten the dust extraction hose from underneath the main saw unit and thread through the extraction hole in the side on the machine Fig. Page 12 4. If it is out of Fig. Page 12 Slide the fence rail into the gap left between the table and the star knobs then tighten the star knobs to secure the fence rail.

Page 13 7. Machine Assembly - Cont. Fitting the Rip Fence Fig. Fence Alignment 1 Fig. This is done by slackening the four wing nuts on the fence rail Fig. Use the angle indicator scale on the trunnion bracket to find the desired angle. Re-tighten the lock handle to secure the table. Page Bandsaw Blade Set Up 9. Before carrying out any adjustments or maintenance ensure that the machine is isolated and disconnected from the electricity supply.

The blade tensioning knob Fig. Page 16 To avoid over-adjusting, make small gradual adjustments on the tracking knob and revolve the bandwheel on a few times to check the alignment of the blade before making further adjustments. Page 17 9. Bandsaw Blade Set Up - Cont. Adjusting the Upper Guides Fig. First check that all the roller guides are moving freely.

To adjust the upper blade guides, first position the guide assembly relative to the blade by slackening off the grub screws Fig. Page 18 The upper blade guide should provide approximately 5mm clearance above the work piece. This machine is not suitable for cutting metals. Page 21 Connection of the Electricity Supply - Cont. Switch the machine on by pressing the green button in the switch unit.

Switch the machine off by pressing either the outer red button or inner red button on the switch unit. Note: Depending on the condition of the electrical mains supply, slight voltage reductions may occur when the machine is switched on eg momentary Page 23 Remove the faulty component and replace only with genuine Record Power replacement parts.

Any electrical components should only be replaced by a suitably qualified person. Page Blade Selection Page 27 By making and using custom jigs repetitive and accurate work can easily be achieved, the following illustrations are some examples of typical jigs and supports used on a bandsaw.

Page 28 Ex. Jig for accurate repetitive wedges.

Mini Hand Plane Set 7 11 Woodworking Tool Shops Near Me 03