User Manual: Craftsman CRAFTSMAN SEARS BELT AND DISC SANDER - Manuals and Guides View the owners manual for your CRAFTSMAN SEARS BELT AND DISC SANDER # Home:Tool Parts:Craftsman Parts:Craftsman SEARS BELT AND DISC SANDER Manual. Open the PDF directly: View PDF. Page Count:   FOr illustrative purposes, the Belt and Disc Sander=isshown mounted on the Craftsman Catalog No. ; Steel Leg set. This Leg Set is included with Model No. / 1_ Place the.  The above recommended accessories are current and were avai{able at the time this manual was printed. i. Answers. Re: Mastercraft disc and belt sander manual. Wen is the best disc/belt sander in the modern time. Price is reasonable. Easy to use.  try to rig the nozzle of a shop vac to the part where the bag would normally connect and run the sander simultaneously with vac for a few minutes and see if that helps. Posted on Jan 11, Helpful 0. Mastercraft 4 x in Belt/Disc Sander features a amp motor with ½-hp. 4 x 36" (10 x cm) sanding belt. 6" ( cm) sanding disc. Rocker switch with locking key. GiveAway ended: 31st January,   Follow common safety rules and precautions as outlined in any manuals related to the equipment being used. If advice or other expert assistance is required, the services of a competent professional person should be sought. Use of Canadian Woodworking site and Forum.  www.- may amend this policy from time to time. By using this site, you agree to the terms of this Privacy Policy. Canadian Woodworking reserves the right to make changes to this policy at any time. Please check back periodically to review any changes. Questions or Suggestions. Previous Page. Do not use damaged extension cords. Motor stalls resulting in 1. Page 13 Sanding operations are inherently dusty. Take the sander to a qualified service technician for this type of maintenance. Position table support against table bottom, aligning holes on support with pre-drilled holes in table.

Toll-Free Helpline: Table of Contents. Previous Page. Next Page. Sander MasterCraft Instruction Manual 11 pages. Failure to observe any of the following instructions could result in severe personal injury to tool user and bystanders or cause damage to tool and property!

Page 5: Before You Start Operating Instructions Before You Start — Electrical In the event of a malfunction or short circuit, grounding provides the path of least resistance for electrical current and reduces the risk of electric shock for the operator.

This tool is equipped with an electric cord that has an equipment grounding conductor and a grounding plug. Repair or replace damaged or worn cords immediately. Be sure your extension cord is properly wired and in good condition. Do not use damaged extension cords. Carefully remove all parts from the shipping carton.

Page 8 Installation of Sanding Disc and Guard 1. Peel backing away from sanding disc. Locate table support and 3 hex head screws, washers and locking washers in loose parts bag.

Place table top-down on a flat surface. Position table support against table bottom, aligning holes on support with pre-drilled holes in table. Page 10 Installation of Belt-Sander work support 1. Locate work support and hex screw, washer and locking washer. Hold work support in position and fasten as shown. Do not overtighten. Turn the power off and remove the plug from the outlet before changing the accessories.

Removal: 1. Slide tension lever to the right to release the belt tension. Slide the used sanding belt off of the rotational mechanism. Installation: 1. Page 12 To properly track the sanding belt: 1. See also: Instruction Manual. Read and understand this instruction manual thoroughly before.

Table of Contents. Previous Page. Next Page. MasterCraft Instruction Manual 14 pages. Page 3: Technical Specifications contact us 1. The safety symbols and their explanations require your full understanding. Page 4 contact us 1. Page 5: Key Parts Diagram contact us 1. Page 6: Important Information contact us 1. Page 7: Assembly Instructions contact us 1. Page 8: Operating Instructions contact us 1.

Keep all ventilation openings clean. Avoid using solvents when cleaning plastic parts.

Big Wood Sanding Machine Inc Claphams Salad Bowl Finish Review 5g