Make A Frame For Mirror Data,Best Place To Buy Woodworking Tools Quick Pdf,Starrett Woodworking Jigsaw Blades,Cool Wood Bench Ideas 2020 - Videos Download
07.05.2021We learn as we go around here. Progress over perfection, amiright? Big time. Quick disclaimer: this post contains affiliate links. By using them to make a purchase, I may receive a small Make A Frame For A Bathroom Mirror Card commission at no extra cost to you. Thank you in advance for contributing to my blog and supporting my Target addiction. The ornate silver frame you see in my before images actually started out as a faux wood frame.
The frame was a plastic material that I spray painted gold a while back and then re-spray painted silver. The spray paint helped a bit Finally, last week I was absolutely fed up with looking at it and decided it was time for a real change. Keep reading till the end to see what the mirror looks like now. My original plan was pretty simple—build a thin wood frame around the entire mirror using 1x2 strips.
Then, I planned on using 1x4 strips across of the back of the frame like slats on a bed framesetting the mirror inside the frame, and glueing it to the slats. Unfortunately, I never got that far. Here are all the ways that my orignal plan went wrong so you can save yourself the trouble:.
I bought the cheapest lumber I could find. I really wanted the mirror to have a thin frame with a slight ledge, make a frame for mirror data I used 1x2 lumber strips cut to my dimensions. The thin strips were pretty hard to drill into and ended up splitting when I tried to screw the frame together.
The wood was too thin. I tried to recreate the thin, metal mirror look by using thin strips of wood and just…no. Do yourself a HUGE favor and make sure you buy straight lumber.
Like no bowing at all. The strips across the make a frame for mirror data laid make a frame for mirror data top of the frame rather than inside it. This on is a little hard to explain in words so try to bear with me. I cut the back strips to lay on top on the assembled frame, with the screws going down into the frame. I should have cut the strips to fit in between the sides of the frame, with the screws going in from the sides.
I painted the wood. Staining the wood looks better IMO. Spend the couple extra bucks, double check that your wood is straight, and use a full sheet of plywood as the back of the mirror.
I already make a frame for mirror data the mirror, gorilla glue, screws, and drill —but I did have to make a frame for mirror data. These were the prices at my local Home Depot.
Prices vary by location. Since I used a framed mirror I already had, I had to remove the old frame to get the exact measurements of the mirror itself. I removed the paper backing and the cardboard corner pieces. After that was done, I carefully pulled the frame apart on one corner.
Be very, very, VERY careful not to put too much pressure on the mirror or you risk breaking it. Once the first corner was seperated, the rest were pretty easy to take apart. This is pretty straightforward. Use a measuring tape to measure the length and width of your mirror. For my dimensions, two 10ft boards was the most cost effective way to buy the lumber least amount of wasted wood. I had my boards cut to the correct size at the hardware store. Keep in mind that most all?
I wanted the top and bottom pieces to extend Make A Frame For Mirror Excel past the side pieces to create my butt joint, so I did a simple equation:. So for my mirror it would be: 1. The sides should be the exact length of your mirror—so 66in in my case.
My dimensions were 38in x 66in. Anyways, assemble your frame and be sure to line up the boards with the top and bottom pieces outside of the side pieces. I used two 2in screws in each corner to ensure the frame would be sturdy. Leave a little wiggle room for easy placement of your mirror, then tighten the screws once the mirror is in place. Once your frame is completely assembled, lay the plywood board on top of the open box frame and screw it into place. Again, make sure you predrill the holes first and use enough screws to keep the board securely in place.
I use screws on each side. Make a frame for mirror data found it easiest to apply the stain with a paintbrush make a frame for mirror data than a rag. I went over the entire frame twice back-to-back and then let it dry for 6 hours before touching it. With the frame still laying flat on the ground, carefully set the mirror inside of it. Then tighten the screws around the frame. Seriously, how cute is that?! And it was sooo easy to do. The entire project only took a day, and most of that was just waiting for the wood stain to dry before I could move the mirror.
I found the small furry rug at Ross, but here is a similar one at Home Depot for the same price. My Instagram. My Home. Sep Kayla Simone. View fullsize. Now on to creating the new frame. Now time to assemble! Show 5 comments.
Woodwork Quiz Questions And Answers Belt And Disc Sander Risk Assessment Control |
07.05.2021 at 21:42:16 Result in the heat furniture project that has.
07.05.2021 at 21:54:26 Deals on eBay for dust collector." I recently replaced my dust-collection system with Oneida’s new Supercell.
07.05.2021 at 20:19:19 Billion starving people in Africa byjoining.
07.05.2021 at 19:11:15 Buy the Knapheide part you need just sent.
07.05.2021 at 14:21:28 SodaStream maker, using the stopwatch icon, which router Bits Gauges Wood.