USD. /4" x /4" top plate size fits all INCRARouter Tables and some other brands. Not compatible with Rockler or Bench Dog tables. Made in Canada. Click here to open the Router Lift Comparison Chart. The Incra/Jessom Master Lift II had all of the features I wanted plus. First I wanted high precision on both the vertical and horizontal axis, then a lock-down capability to avoid any creep, Incra does this all by design. The lift mounted my Milwaukee router with ease (and can change to Incra Master Lift Ii 500 accept my Porter Cable, Bosch or Dewalt without any extra hardware or shims needed).  There are two things missing that would make this perfect: The pictures in the installation manual are terrible, and there seems to be no way to zero out the lift measurement once you get a bit installed. Read more. Helpful. Pairing the AEG with the Mast-R-Lift ll was pure fun. It’s a marriage made in heaven for those wanting ease of use coupled with accuracy. Together with the Incra LS Positioner, you have a combination that is fast to setup and adjust, easy to use and just plain accurate. I can’t say any more than that. This will save loads of time in the workshop. When you lock this lift in position it stays locked in position. Your experience and preferences may vary and there are other options out there, but this is my experience with incra master lift ii inc two lifts, hopefully inrca helps. Change router bits from above the table Make fast, precise height adjustments with positive above-table infra Height scale is marked every 0. Sell on Amazon Start a Selling Account. Like the previous version, the INCRA Mast-R-Lift II allows incra master lift ii inc, incredibly precise height adjustments conveniently made from above the table, and it also provides you with the ability to change router bits lft above. The spindle lock, while labeled with almost half a turn of motion to transition, really only needs a tiny tweak to get it out of locked mode and into free moving mode. Add a router?

Reviewed in the United States on September 7, I have been woodworking for many years now, and a router is a invaluable tool in the workshop. Everything from creating profiles to using it as a jointer to cutting dados and rabbits, the router is the tool. Not only did I have to Incra Master Lift Ii Nz bend down under the table to get to the cam lock lever that secures it to the base, but you needed two hands when adjusting it up or down This leaves no hand to hold a ruler to see if the height is correct.

And most of the time, with the Porter-Cable router I have, the router would change heights when I tightened the cam lock. And with some router bits I could not adjust it low enough before it was coming out of the base.

Now with the Mast-R-Lift I have no more frustrations. I would have bought this thing years ago, but it seemed a bit too expensive for the amount of woodworking I do. Let me tell you No, you can't zero out the dial indicator as some have pointed out, but it is not all that necessary to do this and definitely not a deal killer. The micro adjustments that can be made are fantastic. As an example of saving time and frustration, the last project I did was a crib, changing table, and chest of drawers for my brother and his wife.

I was at the assembly stage on the chest of drawers and a piece of trim which ran around the bottom of the cabinet that I had routed a profile on got messed up and was not useable. This piece had to mate to another piece at the corner with a 45 degree miter, so it really needed to come from wood that had all been routed at the same time so the profile height would be the same.

With Incra Master Lift Ii Online the Mast-R-Lift I was able to match the profile perfectly in a matter of minutes by making small height adjustments and checking it against the part it was mating to. I never would have been able to do this without this tool. I might have gotten close, I might have even lucked out and matched it exactly For me, just that one issue made the purchase worth every penny.

Now I look forward to using my router table. Top critical review. Reviewed in the United States on May 30, This is a really nice lift, I'm almost ashamed to only give it 3 stars.

The build quality is really good and from what i can tell, I shouldn't have any major problems with this lift. I purchased the incra version of the mast-r-lift solely for the fact that I prefer the magnalock inserts Incra Master Lift 2 Year Old versus the traditional inserts that twist lock in place. I've used both, you don't want to twist lock rings. I actually have 2 of these lifts and a woodpeckers sidewinder router lift.

The sidewinder lift is identical to the prl-v2 but it has a side mounted crank as opposed to the surface mounted thumb wheel.

I've never used the thumb wheel, but I am almost certain I would prefer it over the mast-r-lift's top side crank. This is definitely based on personal preference, but the fence on my router table is about 5"-6" tall.

I find that if my fence is set into position it is difficult to use the crank handle that comes with the mast-r-lift as the crank doesn't clear the fence. In this instance, the thumb wheel of the woodpecker lift would prevail. Of course, not everyone has the same height fence. The woodpecker lift has a special quick lift handle that disengages the threaded lift mechanism to quickly raise the router for bit changes.

With the mast-r-lift you have to crank the handle about 40 revolutions to raise the router up to change the bit then crank 40 revolutions to lower the bit back to working height. It is a small complaint. Woodpeckers definitely wins in convenience but I feel Jessem has the upperhand in terms of durability. More about this at the end of the review. On the woodpeckers lift, you can zero out the reference scale to make it easy to track how far up or down you move the bit.

The reference scale on the mast-r-lift can not be zeroed but it is definitely easier to read. On the mast-r-lift there is a lock that can be activated to prevent accidental height changes. This is a really thoughtful feature. The mast-r-lift has 2 lateral adjustments to secure the lift in the table. For lack of better terminology, I'm going to call them tension cams. The tension cams apply lateral force to "jam" the plate in place.

The woodpeckers lift uses a threaded rod mounted to the underside of the plate with aluminum blocks and knobs to secure the plate from underneath the table. I feel the woodpeckers method is definitely more secure. The leveling method on each lift is identical.

The mast-r-lift has the built in option to mount a number of different routers. I have a milwaukee in one and a porter cable in another. With the woodpeckers lift, you need the correct set of mounting pads to accommodate your specific router. When my milwaukee went out on me in the middle of a time sensitive project I wasn't able to source another in short order.

I had a spare and fortunately amazon had the mast-r-lift available with prime shipping because i don't have the porter cable pads for my woodpecker lift. Jessem definitely did this part right. The lifting mechanism of the mast-r-lift is very robust and very well built.

Without a doubt i feel it is much stronger than the woodpeckers lift. My woodpeckers lift actually quit lifting a few years ago. I contacted woodpeckers and they shipped out a fix promptly. Apparently the quick lift of the woodpecker lift has a couple wave washers and a cam nut.

I was using the heavy milwaukee and the cam nut stripped out. Woodpeckers sent a new cam nut and a couple extra wave washers, since then I've had zero problems. Although the quick lift is susceptible to wear, as long as woodpeckers stands behind their product, i would consider the quick lift an almost mandatory feature on a router lift.

Overall, in my own personal preference, i prefer the woodpeckers lift due to the fact that bit changes are quick and adjustments to height are easy without having to use a crank handle that may or may not clear your fence. The rigidity of the mast-r-lift and the one size fits most approach definitely hold a lot of value.

Your experience and preferences may vary and there are other options out there, but this is my experience with these two lifts, hopefully it helps. Sort by. Top reviews Most recent Top reviews. Made in U. Like the previous version, the INCRA Mast-R-Lift II allows fast, incredibly precise height adjustments conveniently made from above the table, and it also provides you with the ability to change router bits from above.

The quarter-turn cam lock is operated from the top using the lift crank to eliminate height drift. The previous generation was effectively bomb-proof, and we expect the new model to continue that reliability. Allows fast, precise height adjustments and changing router bits above the table. Direct-drive, super low friction, and compatible with wide variety of fixed base routers without the need for adapters. Not compatible with Rockler or Bench Dog tables.

Made in Canada. Click here to open the Router Lift Comparison Chart.

Custom Clothing Brand Logos Bench For Wood Carving 5g Used Woodworking Machinery Canada Research