Flex Cut Knives Error,Woodworking Bench Tools For Sale 50,Half Inch Shank Router Bits Zip,Black Walnut Table Legs Vessel - Plans On 2021
12.11.2020Table Of Contents. Quick Links. No Online registration might delay response to your. Table of Contents. Previous Flex cut knives error. Next Page.
No Online registration might delay response to your flex cut knives error and service enquiries. Flwx 2 Caution! Changes or modifications, not expressly approved by Summa, who is responsible for FCC compliance, could void the user authority to operate this equipment.
Unauthorized copying, modification, distribution or display is prohibited. All rights reserved. Contact Information All inquiries, comments ckt suggestions concerning this and other Summa manuals Page 6 CAL. Page 10 Overcut for easy weeding. General Information The SummaCut-series will only perform according to specifications if a genuine Summa knife, pen or pouncing tool is installed.
Do not replace the standard knife, pen or pouncing tool with products from other manufacturers. Dut order not to damage this part, errror attention is requested when putting a machine on a surface. Figure explains the right position. It allows a high-speed serial bi- flex cut knives error communication between the host computer and the cutter.
Dlex 21 Pinch rollers: - The knjves rollers one at each side hold the media clamped flex cut knives error the knivves rollers and the media drive sleeves. Cutting strip: - Soft strip to avoid any damage to the knife tip f,ex no media has been loaded. The ground conductor must have the same size, insulation material and thickness as the grounded and ungrounded branch-circuit supply conductors, but the insulating sheath should be green, or green with yellow striping.
Cuf of an ungrounded outlet exposes the operator to risk of electric shock and will also lead to malfunctioning of the cutter. When using sheets, there are two possibilities. First of all, when using long sheets, roll up the sheet so that the alignment is identical to that of a roll. Secondly, when using short sheets, the alignment is not so important. When loading media, adhere to these khives instructions strictly.
The pinch roller can be lowered anywhere between the two detent positions of the long drive sleeve to allow for flexibility in holding any media width. Page 27 The pinch rollers should be positioned over the drive sleeves about 3 to 15 mm 0. Ideally, the pinchroller should divide the media in equal parts and above flsx drive sleeve. The cutter is now ready flex cut knives error the actual load procedure; it starts once the pinchrollers are closed.
Lower the pinch roller flex cut knives error to press the media firmly against the drive sleeves. The knife blades may cause serious personal injuries if handled without proper care. Use extreme care when operating the cutter and when installing, removing or handling the knife! To set up your cutter for knife operation, proceed as follows. Turning the cutting depth adjustment screw anticlockwise will decrease the cutting depth. When fleex offset value is set knjves high, the rectangles will be distorted.
Increase the knife offset with the key when squares seem rounded in the corners. After replacing the knife with a pen, the cutter can be used as a plotter to draw draft plots flrx new or existing designs on paper.
After replacing the knife with a pouncing tool and Cnc Wood Design Cutting Machine Error after putting Flex Cut Knives 2020 the special strip on the cutting strip, the cutter can be used as a pouncer.
The main functions of the liquid flex cut knives error display LCD and the control panel keys are explained in the following paragraphs.
A last menu item in the row gives access to a submenu with which all the other functions of the cutter can be reached see flex cut knives error 2. As long as this key is not pressed a changed value of a menu item is not flex cut knives error internally and can will be lost if the menu is left. After pressing the key, press the jogging key until the desired speed The default knife pressure fldx flex cut knives error grams.
After pressing the key, press the jogging key until the desired pressure is displayed on the LCD and press to confirm. The default pouncing pressure value is grams. It should be taken into account that access to some of the submenus will be determined by the plotting language flex cut knives error are using. Four different user configurations can be saved. The LOAD instruction is used to initiate a load sequence.
Press the key to execute. The origin can be changed first flex cut knives error necessary. Press the jogging key to change the origin in the Y-direction. Figure gives the different options in this submenu. When the cutter is set to fast or accurate, it will alternately cut one length with full pressure, and one length with reduced pressure. The feature FLEX-CUT offers the advantage that it cuts completely through the material, yet allowing the material to stay together by means of the small media rlex.
This is useful for flex cut and media which is difficult to track. The different panelling parameters can be accessed by pressing the jogging key. Press the jogging key to change them. After pressing the key, press the jogging key until the flex cut knives error language is displayed on the LCD and press to confirm.
The default baud rate is bps. After pressing the key, press the jogging key until the desired baud After pressing the key, press the jogging key until the desired setting is displayed on flex cut knives error LCD and press The ertor detects the end of media. In that way the sensor prevents damage to the cutting strip and knife tip. After pressing the key, press the jogging key until the desired setting Errlr the upper line of the display the desired pressure appears and in the bottom line of the display the value that has to be sent to the head to reach this pressure this knivea is between 0 and To change the parameters press the key.
Then use the jogging keys the go through the different parameters and change the values with the jogging keys. The selected configuration number is marked at the bottom of the menu window. Standard included are the manual alignment errkr. Depending on the selected alignment method, the cutters can counterbalance the following irregularities: flex cut knives error. These cross-marks can be of any type. There are three alignment methods. Alignment Flex Cut Tools Quote methods: 1. For this method, the origin and one point along the x-axis must flez specified.
For this method, the origin, one flex cut knives error along the x-axis and one point along the y-axis must be specified. This method rotates and skews the drawing. It does not need any distance parameters. This way kjives will not catch the eye if the contour cuf moved a little during cutting. See section 2. For the two other methods: position the knife tip exactly above the cross- mark flex cut knives error the Y-axis marker using the jogging keys.
When above the marker press the key. If there are no such instructions, follow the explanation below. They are virtually friction-free and require no lubrication.
They will, however, collect dust and lint, which may affect the performance of the cutter. Keep the cutter as clean errpr possible by using a dust cover. This situation may cause malfunctioning of the cutter. To clean the sensor area, proceed as follows: 1.
The fuse is at the back next to the power inlet refer to fig The fuse rate is T2. Select the port that is connected to the cutter and click on the properties button. This will automatically install the driver and the Summa Port Mapper utility. Restart the computer. This manual is also suitable for: Summacut dse Summacut d Summacut d60 Flwx dse Summacut d60se. Print page 1 Print document 75 pages. Cancel Delete. Sign In OR.
|
Letter J In Mandarin Ppt Behlen Salad Bowl Finish Ingredients Forum Snap On Bench Vise For Sale Verification Jet Air Filtration Afs 500 80 |
12.11.2020 at 13:12:13 Cordless plate bottom Line The Osborne EB-3 Miter Gauge has.
12.11.2020 at 19:21:37 Was in a hurry with winter but do let it dry between.