Make some stunning wooden lanterns using scrap wood in just minutes and add them to your garden for day and nighttime beauty.  After deciding to make some solar wooden lanterns, I was on a mission to find the perfect solar light. I searched multiple stores but could find one I love, then I found this one and fell in love with the glass globe, and then that evening, I was dazzled by the shadow it casts. Solar DIY Outdoor Lantern. How to Build Scrap Wood Lanterns. Gather your supplies. Drill (with drill bits).  I am wondering how the lights charge with the wood top over them? Do you have an issue with this? Thanks. Reply. Jeff Landers says. September 24, at pm. Where do the solar panel, batteries and wires go. Reply. Peter DIYPD says. Do It Yourself Wood Round Headboard. X-Shaped Magazine Holder. Reclaimed Wood Floating Shelves.  There’s nothing wrong about choosing to build small DIY woodworking projects for beginners first. And who says you have to build Do It Yourself Wood Lanterns Twitter a big-size tree house or a complicated piece of furniture, anyway? Woodworking and DIY projects at home don’t always have to be made on a larger scale, especially for beginners who don’t have the information and space yet. You can create something with a 1-sheet plywood, and it would give you beautiful results while being easy at the same time. You don’t need a lot of materials or space. DIY projects like a chair or simple gifts for kids can be made even if you have. A wooden eggcup in the shape of an Easter Bunny. Your friends and family will love this gift made from laser cut wood.  We used alder wood for making the eggcup. But it will also work with conventional plywood; ideally use poplar plywood for laser cutting. Preparation. Required material: 3 mm alder wood or poplar plywood. 1 Easter egg. Used Trotec Laser: Speedy 60 watts. inch lens. Tips: Do It Yourself Wood Lanterns Quotes Use a cutting table. I have fond memories of one year when, in the middle of our dinner, it started to rain. I now live in the UK, but I Jill Marshall - Under A Cottonwood. My name is Melissa and I am a fellow blogger at sincerelysaturday. That's the whole point.

So, anyway, last minute like seriously three days before Christmas , I decided to make them wooden lanterns. I spent almost my entire Christmas break every spare moment I had in the shop whipping these up. It was a fun yet time consuming project because you have to let all the wood glue dry after every step. This post contains affiliate links for your convenience. If you purchase from one of these links, I may receive a small commission at no extra cost to you.

Thank you for supporting this blog so that I can continue to post free content. Please see disclosure policy for more details. Wood Glue. Masking Tape. Jig Saw optional. Miter or Chop saw. Nail and staple gun. Clamps you can never have too many. The top of the lantern is the hardest part. But, you can do this. Trust me. Then, I tilted my table saw blade to 45 degrees. First, I set my thingy-ma-jig to about 20 degrees I have no idea what these things are called, but they come with table saws and you can adjust the angles with a twisty knob on top.

Just see picture below. You could use a taper jig instead, or make your own thingy-ma-jig. And I cut off the end of a board at that angle. This is where the next cut will be.

I lined it up with the blade and adjusted the rip fence to where it was just touching the bottom corner. Just in case you were wondering when my hands became so manly looking. I ran this through the saw just like this with the corner running along the fence, then flipped it over and did it again and again and again and again does that make four yet? Then I ran them through the saw again with the blade tilted to about Once all the pieces were cut, I lined then up and drilled a decorative hole in them.

This step is optional, but it makes it look nice and helps with the gluing later. So the cut bevels are on the bottom Do It Yourself Wood Lanterns Weight side. I just got mine as close as I could.

Then I flipped it over and filled the joints with glue. It will be messy. Be prepared. I put some glue on the two outside edges, then folded it together and taped the final joint. Then I took them inside to let the glue dry really good overnight. These things are a little fragile. I made four lanterns and had some leftover. If you do that, however, be mindful of your measurements because they will not be the same as mine.

This was so the plywood bottom could be supported. Then I glued around the edges of the plywood and slid it in place and clamped. This part is so easy. I just made four panels one slightly smaller than the rest for the door and nailed them together.

I glued all the joints, then stapled them together only on the back side. Then I clamped them until the glue dried. They would make lovely gifts. I stumbled across this on Pinterest and I love it! I will definitely be trying this soon. I really like the two sizes you had on your mantel. Thanks, Abbigale!!

It really is pretty easy! Terrific lanterns. I echo the sentiments of our friends above. This is on the absolutely must do list. Any ideas? Thanks much! Would you please send me a summary of each part and their dimensions. As I live in South Africa and we work in metric measurements it is confusing to work from the dimensions in the article.

Thanks Malcolm. This is a silly question but the pieces for the top i know you said he used a miter saw on it but what thickness is that wood? I tried to find an email to get back to you Hi there, Lori - these are, by far, my favorite lanterns! I love the beveled top. Would you mind asking your husband how he cut the bevels, please? Wondering about the angle. Thank you. Merry Christmas.

Hi Audrey! Thank you! Well, when we made them we used a 2x4 for that part and used the miter saw to cut the bevels. I don't think we actually measured it, just kinda winged it We had more scrap to play with. The taller one is about 18in. Hope that helps! In the directions it does not mention 2X4 but in a reply to Audrey you mentioned using a 2x4 love your design. You are so right!

Those were used for the frame of the lantern. I gave the wrong size of the top to Audrey.. Those were cut out of a 2x8. I need to update this post to make it more understandable! Thank you for pointing that out to me!! Blessings, Lori. Love your design! I assume the top is attached. Have you tried a real candle or would it generate too much heat for the underside of the top?

Yes, the top is attached. Not really sure about a real candle. Maybe if it was a short one Comments are awesome! Let me know what you think! January 7, - 30 comments. It all started when I wanted something new for the mantel. I dragged Hubby all over town shopping for lanterns.

So, we came home empty handed. I started searching online for some inspiration. Hubby and I put our heads together and this is what we came up with.

Wood Turning Lathes For Sale Norris Marking Knife Online