Something that would make ahop life easier and my productivity questiions. In my head, it would be a ton of ducting running all through my shop. The intimidation factor of that was so high that I just kept putting it off. Not to mention how much it was probably going to cost in materials. Besides, if you have been following me for any amount of time, you know I HATE to have things permanently stuck in one place.

Yes, I understand that a wall mounted dust collector goes against what I just said. This is the one exception! While the dust collector is static, the tools I use are all mobile. If I want to move them I can! Sust getting started installing the dust collector, unbox all diy shop dust filter questions the pieces. The diy shop dust filter questions collector and canister filter come with detailed instructions.

Decide where you would like the questuons collector mounted. Make sure there is an outlet nearby. Find the studs and mark the center point on diy shop dust filter questions of them.

These marks will be where the dust collector mounts. Use the pilot holes in the wall as a guide for mounting. Ensure the lag bolts are driven tightly into the wall studs. Add the vibration dampening shims to the lag bolts, qudstions with help hang the dust collector from the lag bolts.

Tighten the bolts to the cleats. To install the canister filter, use the included foam tape and wrap it around the outlet port. Attach the flange with the included bolts. With assistance, line the holes on the canister filter up with the flange.

Attach with the included bolts dusst tighten. Attach the agitator arm to the top of the canister and ensure it can diy shop dust filter questions in both directions. Apply foam tape to the bottom of the canister then fit the bag over and clamp in place with the strap clamp.

Attach the Y inlet to the dust collector. Diy shop dust filter questions the blast gates to duust inlet, then diy shop dust filter questions the hoses with hose clamps. To keep the quick change handle and hose out of the way, I installed a docking dly kit. I first attached a backer board to the wall, centered on a stud.

At the top of the board, I installed the docking port with the included screws. Below that, I installed the hose straps, making sure they were level and centered on the board. I attached tool ports to my drum sander, belt sander, joiner and bandsaw.

These allow the quick release handle to be easily moved from tool to tool. With all fikter the ports attached, I then moved my tools to their new locations. I built mobile bases for my drum sander, bandsaw and joiner to allow ease of movement quwstions using the tools. They are also set up in a much better way to allow for increased productivity when moving from tool to zhop. This corner of my shop is now so much cleaner and more efficient with the layout.

The quick change shop and tool set also comes with spring clamps that I installed on the wall. These keep the floor sweep and bench nozzle up and out of the when when not in use. I used to dread using my large tools because hooking them up to dust collection was difficult. My new quick change handle questiobs the job so much easier.

The floor sweep and bench nozzle make cleaning a breeze. Special thanks to Rockler Woodworking and Hardware for partnering with me on this qusstions. They will answer any questions for you and will also have fiter suggestions on the best way to go about doing it.

Like I said before, my plan was far more complex than it needed to be. I am so glad I contacted the support team and they lead me in a much better direction! Your email address will not be published. Save my name, email, and website in this browser for the next time I comment. Addicted 2 DIY is a participant in the Amazon Services Ddust Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to amazon.

For online roundups, authors are welcome to use 1 image from a particular blog post with a direct and visible link xiy to my site. You may not alter the images, remove watermarks, add text, or remove text from the images used. Images may not be printed, or used in a print publication without my expressed consent. Join my newsletter list to be the first to hear our latest news!

Diy shop dust filter questions More Close Top Banner. Sharing is caring! Pin Share Tweet. Leave a Reply Cancel reply Your email address will not be published.

Footer Affiliate Disclosure Addicted 2 DIY is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed diy shop dust filter questions provide a means for sites to earn advertising fees by advertising and linking to amazon.