I went with oak because that is what my cabinets are. I am thinking i am going to fill it but i am not sure if that will make it look right. All you have to do is measure the opening of the cabinet and then add the desired overlap. The inside of ours was not pretty at all. See our favorites in the shop. Sand the shakker and apply a diy shaker kitchen cabinet doors jack, paint, lacquer or stain in the color that kitcheh have chosen to match the interior of diy shaker kitchen cabinet doors jack kitchen. I measured all my doors and decided on going with a trim width of 2.

I think the rail measurement is 1 inch short. I think the rail should be 16 inches for the door to be 18 inches wide. Great tutorial and information. Never glue in panels because it does not allow for expansion and the door will eventually warp. Instead, glue only the stiles and rails.

I believe that she means that you make the groove a half inch deep. You are correct that it should be a quarter inch wide. By the way, a groove is not exactly the same thing as a dado.

A groove is with the grain. A dado is perpendicular to the grain. The close up pic of what the tongue should look like really confused me until I realised it did not match the final example pic. The first pic shows something you will never see if you follow the text.

Great Project. Cross cutting with a fence is a potentially dangerous practice as well as free hand cutting the tongue cuts. Remodelaholic is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to amazon.

Please see our full disclosure here. Get organized! See our favorites in the shop. Pinterest Facebook Twitter. Determine Cabinet Opening. This is an example of a dado. Completed dado. Fit pieces together. Slide in center panel to check for fit. Apply glue to each groove.

Clamp the cabinet door. It can be. I'll show you how. Comments I think the rail measurement is 1 Diy Shaker Cabinet Doors Router Inc inch short. Shoot a pin nail centered 1 inch from the top and 1 inch from the bottom. Hold both strips with clamps until the glue is completely dry. To make the horizontal lines, you need to measure the distance between the hardwood strips at the top and bottom and cut hardwood strips for the top and bottom. Apply glue at the back and place the horizontal strips.

Shoot a pin nail through the strips and place clamps on them as well until the glue is dry. Sand the corners and apply a primer, paint, lacquer or stain in the color that you have chosen to match the interior of the kitchen. Analogous colors and like color schemes are really easy to have knowledge of. It is true t…. Necessary cookies are absolutely essential for the website to function properly. This category only includes cookies that ensures basic functionalities and security features of the website.

These cookies do not store any personal information. Any cookies that may not be particularly necessary for the website to function and is used specifically to collect user personal data via analytics, ads, other embedded contents are termed as non-necessary cookies.

It is mandatory to procure user consent prior to running these cookies on your website. Like this: Like Loading More In Interior Design. How to create the most beautiful analogous colors combinations Analogous colors and like color schemes are really easy to have knowledge of. Awesome tutorial! What a great transformation! Looks so updated and fresh now! Hi there! Love the transformation — just curious, did you just do the doors or did you do something with the insides of the cabinets as well?

What do they look like when they are opened? Thanks so much Chloe! I painted the bases and the insides of the cabinets as well, so when they are opened everything is white… well except for my mess of dishes ; Have a great night! I have similar cabinets that I want to change up and your tutorial is exactly what I was looking for.

I had a question about the drawers — did you trim them out or leave them flat? Most of my bottom cabinetry is drawers so I was trying to decide what to do. Hi Kylie! Sorry for the late response. If I had larger drawers I probably would have trimmed them out as well. Let me know if you have any other questions! Ashley, your tutorial is amazing! I have the same type cabinets with the rounded edges.

You mentioned that in the tutorial but I was wondering if you filled in the gap between the door and the new trim? Thanks for the inspiration to redo my own :. I am interested in this as well. Have the rounded edge cabinet and would LOVE to do this. Has anybody tried? I realize this was posted quite a long time ago and the OP, followers or blogger may not see this, but I am interested in the answer to this question or to seeing pictures of what the inside of that external edge looks like when you open the door.

Would wood filler work for that? I know you said yours are slightly rounded, mine are noticeably rounded. I have these exact same doors and have been playing around with the idea of doing this exact same process with them for years.

I was worried that they would not look good enough. Now I am totally inspired and have decided to go ahead with it. Thank you so much for all your wonderful information. I know I will be using your blog a ton to help me with this project. Thanks so much!!! These are stunning and will certainly be part of the project.

Can u tell me if you primed and painted the inside of your boxes? Is that something you regret either way? The inside of ours was not pretty at all. Hope that helps! Thanks for stopping by! About how much did this cost you? I know our kitchens are not the same size or can probably be compared but would love some idea for our tiny kitchen! We are currently doing this exact tutorial on our cabinets. We are sanding everything as smooth as we can get but the nature of the plywood is to peel so it has me worried!

Wondering how they held up over the years : thanks! And thanks for making this tutorial for us to follow! It will save a fortune and many hours of filling and sanding as well. Oh yeah. Another thing. Buy your handles from Amazon. Same is true of self-closing stainless hinges. I love this! We are in the process of buying a home built in and we are redoing the kitchen. Same flat doors with rounded edges except ours look like they have about 10 coats of paint on them!

So I was searching on how to change them and came across this blog! I will be trying this for sure! FYI, in our home we are presently renting, I updated our kitchen with some inexpensive changes. I found these sites and will always go here first for all my hardware, knobs and pulls. I get them from either 99 cent knobs or knob deals. Well worth it! Thanks for posting this!

Love your kitchen redo! What size did you use and how thick are your cabinets? Thanks, George. I love this idea and want to do my kitchen. Did you line it up with the top of the rounding, leaving a little door showing outside the trim? Or did you line it up with the edge of the door? I am also wondering this exact thing. I am thinking i am going to fill it but i am not sure if that will make it look right.

From the pictures it almost looks like she left the rounded edge, but its hard to know for sure. I really appreciate it. Hi I am trying to do something similar to my cabinets but my plywood is just not smoothing out as much as I would like, did you have a problem with your plywood strips not ending up smooth enough?

This helps the smoothing process! Let me know if that helps or if you have any more questions! Thanks so much!! Thank you! You have great tutorial here! I have been wanting this shaker style cabinet for long. Now, I am thinking to pursue remodeling my kitchen, at first I decided to just repaint my cabinet with white color but I have change my mind, I will now try my favorite shaker style. I hope my family will like this. I was wondering the same thing so I did some searching.

I am seeing that most people use a brad nailer, 18 guage for the trim. Not sure if that is what she used though. Following your guide. It still looks good. I used cabinet grade birch. My carpenter is putting on the strips and I will go from there. Thanks so much. I decided to be a DIYer and turn my cabinet doors into the Shaker style.

I work full time and then come home to my 2nd job of the kitchen remodel. I had Lowes cut the strips. I have to sand all the edges.

I then glued and clamped them to the door. Next night, I have to prime with 2 coats of BIN as the doors are stained dark brown. Then, the next couple nights painting both sides of the doors. I have 18 doors to do. I only have 11 finished. Well, over the weekend, I started putting the handles on the drawers. Took me 3 attempts to get them on straight.

TIP…use a nail to start a little whole before drilling the whole. I then tried hanging a couple doors…UGH!!! The first one I did was fairly large.

Belt And Disc Sander Makita Shirt Woodturning Supplies Ireland 06