Upload from URL. Page craftsman variable speed plunge router notation Protective Plunge Post Bellows protect guideposts from woodchips, dust, and moisture. Page 7: Service Safety Always check the tool for damaged parts before use. When used with Before attempting to use any tool, familiarize yourself recommended accessories, such as a router table, edge with all operating features and safety requirements. The high speed of the cutter bit during a proper feeding operation left to rightresults in very little kickback under notafion conditions.

Summary of Contents for Craftsman With proof of purchase, defective product will be replaced free of charge. Page 3 The purpose of safety symbols is to attract your attention to possible dangers. The safety symbols and the explanations with them deserve your careful attention and understanding. The symbol warnings do not, by themselves, eliminate any danger.

The instructions and warnings they give are no substitutes for proper accident prevention Please study them and learn their meaning. Proper interpretation of these symbols will allow you to operate the tool better and more safely.

Read the operator's manual carefully. Learn the applications, as well as the specific potential Do not use the tool while tired or under the influence of drugs, alcohol, or medication. A moment of inattention while operating power tools may result in serious personal injury.

Page 7: Service Safety Always check the tool for damaged parts before use. Before further use of the tool, a guard or other part that is damaged should be carefully checked to determine if it will operate properly and perform its intended function. Check for misalignment or binding of moving parts, breakage of parts, and any other condition that may affect the tool's operation. Page 8 Use only identical replacement parts when servicing a tool. Follow the instructions in the maintenance section of this manual.

Use of unauthorized parts or failure to follow maintenance instructions may create a risk of electric shock or injury. Page 9 To use cutter bits with a larger diameter, install and use a sub-base with a larger opening sold separately at Sears stores or other Craftsman outlets. Use of large Disconnecting the Router will prevent accidental starting, which could cause serious personal injury. When unpacking the box, do not discard any packing materials Your router has a precision-built electric motor and it should only be connected to a volt, Hz AC power supply normal household current.

A fraction of a second of carelessness is enough to cause severe injury. Page 14 Protective Plunge Post Bellows protect guideposts from woodchips, dust, and moisture. Spindle Lock for easy 1-wrench bit changes. To use cutter bits with larger diameters, use sub-bases with larger openings, sold separately at Sears stores or other Craftsman outlets.

Remove all accumulated pitch and gum from cutter bits after each use. When sharpening cutter bits, sharpen only the inside of the cutting edge. Never grind the outside diameter.

Page Adjusting The Depth Of Cut With the motor housing slot C aligned with the plunge base pin D , lower the motor housing into the plunge base, engaging the pin into the slot. Slide the motor into the base as far as it will go. Close the motor clamp securely. NOTE: For all fixed base routers, the cutter bit depth equals the amount of the cutter that is exposed below the surface of the sub-base.

Page Depth Adjustment With the cutter bit already installed, press in the Coarse Adjustment Knob B and lower the motor into the base until the cutter bit is very close to the flat surface on which the base is sitting.

Turn the Fine Adjustment Dial C until the cutter bit "just" To lower the cutter bit, release the plunge- lock lever by moving it "Up" to the unlocked position. Page 23 To set a desired cutting depth, slide the depth-stop rod up until the red line on the clear plastic depth indicator points to your desired cutting depth on the depth scale E.

Secure the depth-stop rod at this position by tightening the depth-rod locking knob C. To micro-reduce the plunge depth, lower the micro-adjustment screw by turning the knob clockwise the desired amount. This green light is always on when the router motor is plugged into a power source. See Figures 5, 6 and 7. When routing a groove that is too deep to safely cut in one pass, it is best to make the cut in several passes. If you adjust it up too far, it will pop off threaded rod.

See Figure Failure to do so could result in dust, shavings, chips, loose particles, or foreign objects being thrown in your eyes resulting in possible serious injury. In order to forward too slowly. When it is advanced into the work save time, do all the cutting necessary at one depth too slowly, a revolving bit does not dig into new wood setting, before lowering the bit for the next pass. Turn router on and let motor build to its full speed. Begin your cut, gradually you are using at the right-hand side.

T heywill follow workpiece edges See Figure The pilot prevents the bit from making too deep a cut; and holding the pilot firmly in contact with the workpiece edge throughout prevents the cut from becoming too shallow. Use of any other Only the parts shown on parts list, page 23, are part may create a hazard or cause product intended to be repaired or replaced by the customer.

Page 24 For repair of major brand appliances in your own home Print page 1 Print document 24 pages. Cancel Delete. Sign In OR. Don't have an account? Sign up! Restore password. Upload from disk. Upload from URL.

Ridgid Radial Arm Saw With Stand Ed Diy Picture To Wood Homemade Lumber Projects Ltd Pocket Hole Jig Vs Biscuit Joiner Song