Sander Parts. Disc Table For more recent exchange rates, please use the Universal Currency Converter. Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. I hope it looks as good as yours when done. The saws were sold through a subsidiary, Delta Specialty Co. Thank you!

Having a welder would have Belt And Disc Sander Axminster Journal been great to repair the side guard. One tool I should have. Last edited: Sep 9, Jeff Horton Member. Messages 4, Location The Heart of Dixie. Bryan, I am guessing that you know this now. But number one thing in any old machine is Belt And Disc Sander Delta 80 completeness!! Are all the parts there? That is the only machine I am sort of looking for BTW.

Jeff Horton said:. Finally done! I got it back together today, took about 7 hours. Glad it's done, having parts spread all over, I could not use the shop for anything else. JPG Al killian Member.

Messages 1, Location Floydada, Tx. Looks great and I am sure it will get lots of use. I rearranged some of the machines to get the sander to fit in along the wall. I had to pull my rolling tool chest out and tuck it behind the TS for now. I better not bring any more orphans home to the shop! I hooked up the DC and did some test sanding Bob Kalamazoo Belt And Disc Sander Journal Luciano Member.

Messages I picked one up about 3 weeks back pretty much complete missing one of the knobs on top and a handle I broke moving it. Yours looks great and thank you for the idea about JB weld mine has the same wounds your did. I hope it looks as good as yours when done. Vaughn McMillan Administrator Staff member. That came out looking sweet, Bryan. Great job on it.

Even sweeter. And Bob, we'll be expecting pictures. Before adjusting, move the belt tension lever A Fig. Place a square B Fig. See if the backstop is square with the sanding belt.

Place an adjustable combination square on the table with the part A Fig. Check the other side of the disc in the same manner Fig. The distances should be the same. Loosen the screw A Fig. Slide the tension lever C Fig. Remove the sanding belt D from both sanding drums. Hold the workpiece firmly and keep your fingers away from the sanding belt. Keep the end of the workpiece against the backstop and move the workpiece evenly across the sanding belt.

To obtain additional information regarding your Delta quality product or to obtain parts, service, warranty assistance, or the location of the nearest service outlet, please call In Canada call Page Warranty Two Year Limited New Product Warranty Delta will repair or replace, at its expense and at its option, any new Delta machine, machine part, or machine accessory which in normal use has proven to be defective in workmanship or material, provided that the customer returns the product prepaid to a Delta factory service center or authorized service station with proof of purchase of the product within two years and provides Delta with reasonable opportunity to verify the alleged defect by inspection.

Print page 1 Print document 23 pages. Cancel Delete. Sign In OR. Don't have an account? Next Page. For Parts, Service, Warranty or other Assistance, Page 2: Safety Guidelines - Definitions If you have any questions relative to a particular application, DO NOT use Delta Combination Belt And Disc Sander the machine until you have first contacted Delta to determine if it can or should be performed on the product.

Make sure your extension cord is in good condition. A machine incorrectly assembled can cause serious injury. Page 5: Power Connections A separate electrical circuit should be used for your machines. This circuit should not be less than 12 wire and should be protected with a 20 Amp time lag fuse.

Page 6: Three Phase Operation 3. Grounded, cord-connected machines intended for use on a supply circuit having a nominal rating between - volts, inclusive: If the machine is intended for use on a circuit that has an outlet that looks like the one illustrated in Fig.

C, the machine will have a grounding plug that looks like the plug illustrated in Fig. If necessary, the motor pulley B can be adjusted on the motor shaft by loosening set screw and moving the motor pulley B in or out as needed.

Nova 1624 Ii Manual 90 Eagle Belt And Disc Sander Valve Gel Stain Application On Fiberglass Door Fa Titebond Hide Glue Lowes 89