Create a beautiful and safe finish on wooden bowls, cups, spoons, and countertops. OIL Finishes. I used multiple thin coats applied with a cloth to a large salad bowel and the results were excellent. Keep wiping it on when you see it has absorbed into the wood, primarily end grain. The product is awesome for finishing end grain butcher blocks of all varieties of wood. By Steven W.

I like this finish. I like this finish I put it on most of my bowls I turn. I do light coats with soft cloth for me works the best. Great finish I use this for all my cutting boards that I make…. Finesse is success!! The product is awesome for finishing end grain butcher blocks of all varieties of wood. I tried several different salad bowl finishes this hands down the best for my uncontrolled climate in Fl.

Easy to use and exceptional finish. It is all I use now for my bowls. Great product I use this on my salad bowl turnings, it dries fast and lasts. Salad bowl finish I have used this finish for at least 25 yrs. Have discovered that by using a piece of cloth to apply it, have had no problems with runs. Good stuff I having been using General Finishes Salad bowl finish for a couple years now. Most of my bowls are pine. I wet sand the first coat with grit to cover any lingering blemishes, then fine sand prior to another two or three coats.

At least 12 hours between coats, more when its cold in the shop. I get a beautiful smooth final finish with a lot of depth. I use a Behlen Salad Bowl Finish Ingredients Company minimum of 3 coats, lightt sand in between on all my bowles, platters and hollow forms. American Specialty Hardwoods rolling pin This is a great product.

I have been looking for a long time to replace polyurethane and finally found it. Great high gloss finish. I made some bowls out of… I made some bowls out of maple and walnut and was amazed at how this product brought out the beautiful grain of the wood once applied.

Question: How would this work on carved wooden spoons that are actually intended to be used regularly for serving food? I am concerned it will wear too quickly. Answer: I own 2 sawmills in Texas.

Additional coats produces a slightly gloss finish. Stands up to daily rinses in hot soapy water. Hope that helps. I use it to restore restaurant cutting boards used daily and not well cared for by staff.

The finish is highly durable and an occasional re-coat maintains the luster. By Steven W. Rust on July 21, It wears well— FDA approved I believe— also I have used it on cutting boards but no as a cutting surface a serving surface and has outstanding gloss —spoons should wear well—several coats making sure dry times— saturating deep in the grain of the wood.

By moemadebb on July 20, Never used on spoons but on cutting boards and after a year the finish is still good. Safe to use and should be great on anything used around food. By Bjohns on July 20, ByPeteon October 13, Verified Purchase I really like the finish on my bowls after at least four coats of salad bowl finish they get a nice gloss to them you can just see the difference on them after each new layer put on. Very good finish and easy to put on. I used multiple thin coats applied with a cloth to a large salad bowel and the results were excellent.

It was best to let dry overnight before subsequent coats also used grit sanding between coats. It is a good product for applications that come in contact with food … Bought and used this a few times. It is a good product for applications that come in contact with food or food utensils. There was a bit of a learning curve for me however. Email: ord ers shellac. Privacy Policy rev. Remove all dust with tack cloth or vacuum hose. Apply Salad Bowl Finish to wood with lint free white cloth. Apply one thin, uniform coat.

Allow 6 hours dry time before re-coating, lightly scuff sand with grit sandpaper. To re-coat, repeat steps 2 through 5. Apply enough coats to thoroughly seal the surface, softer or open pore woods may need several coats. Allow at least 72 hours curing prior to use with food. Clean-up with Mineral Spirits. To insure that materials coated with Salad Bowl Finish may be used in contact with food, you must do the following: Apply to raw non-stained wood.

Use as is Salad Bowl Finish is a ready to use product , do not add reducers. Use only additional coats of Salad Bowl Finish to build a finish do not apply over other finishes. Wait at least 72 hours, observing proper curing conditions, to allow all detectable traces of the Mineral Spirits solvent to evaporate.

Pocket Hole Jig Miter Joint Weight Caddy Right Angle Clamp