Installing a Bench Vise

Woodworking Stack Exchange is a question and answer site for professional and amateur woodworkers. It only takes a minute to sign up.

Connect and share knowledge within a single location that is structured and easy to search. My bench has a 2x4 edge and if I line up the vise where the inner claw is flush so I can mount things vertically, then a under bench woodworking vise questions of the vise overhangs a little.

Would this not be proper? Any suggestions? Update Pics of the install. Over all it seems rigid enough to take on any future projects I may need it for. Where you have your vice placed for the photos is pretty much exactly where I'd mount it, in addition to the front-back placement being ideal it appears to be nearly directly over a leg which gives plenty of support for under bench woodworking vise Best Bench Vise For Under 100 Questions questions heavier work you may do on it.

And yes, it is perfectly fine to mount a vice with a little and sometimes a bit more than that! If you look around any metalworking or machinists' forum you will have no difficulty finding pictures of vices that are mounted well back from the edge of the bench and sometimes this is deliberate, but too often it is because the user didn't realise that if you don't have the vice mounted far enough forward, so that under bench woodworking vise questions back jaw is at least flush with the bench edge, you can never clamp workpieces like this:.

Your positioning is pretty much set, but for future readers it's generally a good idea to give yourself a little extra under bench woodworking vise questions if possible so that the rear jaw projects a smidge under bench woodworking vise questions the bench edge, the reason being at some point you might fit new vice jaws that are a little thinner than the current ones and you don't lose the above advantage if you do so.

Couple of additional points When it comes time to bolt your under bench woodworking vise questions to your bench don't forget your washers, they're especially important up top but you may want to use them underneath also.

I would suggest you pack out the rear mounting lug under bench woodworking vise questions level the vice out. It isn't absolutely necessary to do this, but it's good general practice to have a vice level both left to right and front to back.

You can somewhat surprisingly use card for this — make the packing a little over-thick and it'll compress down when you tighten that nut and afterwards remain remarkably stable. Sign up to join this community. The best answers are voted up and rise to the top. Stack Overflow for Teams — Collaborate and share knowledge with a private group.

Create a free Team What is Teams? Learn more. Best way to mount bench vise for my particular bench? Ask Question. Asked 2 years, 5 months ago. Active 8 months ago. Viewed 4k times. Improve this question. It looks like the swivel base projects out from the inner jaw face so vertical mounting of longer pieces is already a problem.

As this is a metalworking vice I'm voting to close LOL Seriously though, it's perfectly fine to have a little lip of the vice base overhanging the front edge of the bench, the general rule being you want to mouth the vice "as far forward as possible". You're looking for a permanent mount solution yes, you don't need it to be quickly movable?

What makes it a metalworking vice? Lol not that familiar with vices. Metalworking vices have to hold smaller pieces, generally, so their clamping faces are not nearly as under bench woodworking vise questions as woodworking vices. Woodworking vices have faces starting around 6" wide by 4" tall and go up from there.

They also will have more overhang to the sides so that you don't have the issue under bench woodworking vise questions Ashlar brought up though that causes another issue, loss of clamping force from the jaw racking Show 3 more comments.

Active Oldest Votes. Improve this answer. Graphus Graphus Hey thanks for your thorough response appreciate it. The front two mounting holes are positioned on the 2x4 edge.

Would it be best to use lag bolts or long bolts with washers and nuts that go through the entire length of the 2x4? Going into the long dimension of a 2x4 lag screws are almost certainly perfectly sufficient TBH. If the rear fixing needs to be a nut and bolt I would be inclined to use the same throughout only because I'm a bit OCD that way but the projecting nut on the underside could easily get in the way since they're so far forward.

So lags could easily be argued to be the better choice here. Though I might reinforce it from underneath first — ohmmy Oct 11 '18 at Now a 1" top would generally be plenty strong enough, but in your case if it takes little time and costs almost nothing go for it. There's never a good reason not to err on the side of stronger where it might be useful.

One more thing, when choosing the bolts should I get them same diameter as the holes or can they be thinner? Curious if it matters in terms of strength — ohmmy Oct 20 '18 at Show 19 more comments. Sign up or log in Sign up using Google. Sign up using Facebook.

Sign under bench woodworking vise questions using Email and Password. Post as a guest Name. Email Required, but never shown. Featured on Meta. Stack Overflow for Teams is now free for up to 50 users, forever. State of the Stack Q1 Blog Post. Related 7. Hot Network Questions. Question feed. Woodworking Stack Exchange works best with JavaScript enabled.

Jun 01,  · Face vises are attached on the front, or face, of the bench; end vises are installed on the end. The best benches have both, but if you can only afford one, I’d go for a face vise initially. Right-handers should mount a face vise at the far left of the bench’s front edge and an end vise on the end of the bench at the foremost right-hand corner.4/5. Mophorn Wood Vise 9 Inch Woodworking Vise, Heavy-Duty Steel and Cast Iron Workbench Vise, Easy-to-operate Front Vise, Durable Woodworking Bench Vise for Home, Woodworking Studios, Teaching Equipment out of 5 stars /5(K). Jul 02,  · The Eclipse EWWQR7-NA is a great choice for people who do not want to mount two vises to their workbench. It can serve both as a tall vise and woodworking vise. What you get is an adjustable front stop. This feature is designed so as to make the vise used as a tail vise or you can lower it so as to use it as a normal vise.

Dowel Sizes Bunnings 88 Lathe Cutting Tools Youtube Player