Small Parts Holding Router Jig for the Router Table

Using a circle cutting jig makes round router table circle jig js tops so easy. Then you add in the round option. Now, it gets even more tricky because you have to figure out how to cut a perfect circle or figure out how big to make it. First, I will literally list all the tools I used below. The router used in the video is discontinued. Before cutting the table top out, I obviously cut and glued together a panel.

I will cover making an entire table in a later video. To find the center of the panel, I router table circle jig js from each of the four sides and made my marks. This gave me a pretty good indication where the center would be. When you have an odd sized panel you can measure from both directions, for example from the left and from the right.

This will give you two marks close together that you can then split the difference, which is the center. The circle cutting jig comes with several pieces of hardware to attach many different routers. For the record, I have an older Skil brand router, which is why I had to drill my own holes to attach my router. The jig itself is made of a phenolic material so when I drilled my own holes they looked the same as the pre-drilled factory holes.

The jig also comes with two centering pivot pins, which are used as a pivot point to route circles or arches. The jig is tightened down with a star knob to hold the pivot pin in place.

First I drilled the holes for my router. I did this by removing the clear plastic plate from my router and transferring those hole locations onto the circle cutting jig.

I drilled the holes using a tapered drill bit with an adjustable counter sink collar. The tapered drill bit allowed me to router table circle jig js the exact size hole for the screws that are used with my router by adjusting the router table circle jig js sink collar to that location. At this point I attached the router to the jig using the screws for my router and the holes I just drilled.

One thing to mention here is that I left the clear plastic plate off when I attached the router to the jig. This is so that the screws would reach through the jig and screw into my router. The clear plastic piece would router table circle jig js made it too thick for the screws to work. Now that I have attached the router to the circle cutting jigmy next step was to add the pivot pin.

This consisted of a t-bolt, a washer, a star router table circle jig js, and a pivot pin. The t-bolt slips into the recessed track from the bottom and the washer is added from the top onto the bolt followed router table circle jig js the star knob. I just knew I wanted to get the most out of the panel I glued up. So, from earlier, I found my mark in the center of the panel and placed the pivoting center pin there in a pre-drilled hole.

With the pivot pin installed and inserted into the center of the material I loosened the star knob and slid the circle cutting jig to the desired location. This way if the star knob came loose I could tighten it back up in the same place. The phenolic material this circle cutting jig is made of makes it easy to erase the pencil marks.

Actually router table circle jig js the circle was easy. Making sure the router and pivoting pin are secure is key to this operation. The first thing is feed direction.

Router table circle jig js you cut in a clockwise direction, this is known as a climb cut. When using the router in a router table, for example, you want to feed the material from right to left clockwise.

In the video you can see me using the router with the jig in a clockwise motion. I felt comfortable with the cut. Another thing to note while making the cut is to take shallow passes. If you try to take off a lot of router table circle jig js at once you run the risk of burning the wood or even breaking your bit.

Have you ever had a router bit break in the middle of an operation? Not fun. The last thing I want to say is that you might not have a bit long enough to complete the entire cut, for example cutting through an entire 1. The bearing allows the router to ride against the cut you previously made and the cutter will trim anything left behind leaving a flush edge.

This bit has an end guide bearing, so I had to flip router table circle jig js table top to reference the previous cut. I will probably make another table in the future and I will definitely use this jig. I can see where this jig could be useful in other applications like arches.

Leave me a comment below if you have any questions about this jig or about the video. Thanks for stopping by. Outfeed Assembly Table. Modular Shop Storage System. DIY Platform Bed. Stone and Sons content provides how-to videos on YouTube, step-by-step instructional website articles, insightful podcast episodes centered around community and other means of education through online courses and email communications.

Subscribe and listen for tips, advice, opinions, and stories from Shawn and other makers from around the world. Topics range from project ideas, mistakes made, things we learn from, my kids point of view and anything related to woodworking, online content creation or community involvement. Also, please share this post with your friends and family. If you enjoyed this article, please consider sharing it with your friends and family by clicking any of the social media icons below.

It would be greatly appreciated. Enter your information and click the blue subscribe button to receive future blog posts by email. I cut the under side of the table top with the jig first then flipped it. Save my name, email, and website in this browser router table circle jig js the next time I comment. This site uses Akismet to reduce spam. Learn how your comment data is processed.

Sign in. Log into your account. Forgot your password? Terms of Use. Password recovery. Recover your password. Get help. Stone and Sons Workshop.

Shop Projects. Share This Project! Receive our Blog posts! Thank you for signing up. There was an error submitting your subscription. Please try again. First Name. Email Address. We use this field to detect spam bots. If you fill this in, you will be marked as a spammer.

Router table circle jig js Pergola. Live Edge Patio Bar. LED Shop Lights. Please enter your comment! Please enter your name here. You have entered an incorrect email address! Follow us on Instagram stoneandsonsworkshop. Box Columbus, MS

Universal Circle Cutting Jig for Router - Digital Download for Laser Cutting Machines (SVG and PNG), Jig Can Cut 4" to 30" Circles MoonTeaArtistry. 5 out of 5 stars (17) $ Favorite Corner Template Router Table Corner Jig Radius Chamfer Profile for Woodworking 3DPartWorks. out of . Jan 12,  · Drill a hole in the center for a 1/4" bolt. Put a nut on, have the circle marked, bolt in hand drill. Have a belt sander, vertical, in a stand. Turn the sander on, turn the drill on, then proceed to sand down to the desired circle size. Repeat for different sizes. Nov 14,  · first you want to cut the outside of the ring and then the inside of the ring. if you reverse the order and cut the inside first, then you have no pivot to cut the outside. place the outside hole over the 1/4" spiral bit and use a screw thru the center hole to screw it down the the table. cut to the marks.

Quick Wood Projects To Make Money Kit Samurai Carpenter Tool Vest Pattern Diy Wood Planter Box Ideas Pro