Watch our how to use a Porter Cable dovetail jig video in preparation for creating a half blind dovetail joints on your next woodworking project.  Porter Cable Dovetail Jig: Set Up for Half Blinds. Premium Video Preview: Log in or become a member to get full access. Duration: PORTER-CABLE Super Jig. Ideal for woodworking, furniture, and cabinet making. Dovetail Jig Combination Kit enables cutting a wide variety of joinery for drawers, boxes, and furniture.  Even after watching a youtube video prior to ordering it, I still was intimidated at the thought. I bought 3 6'-1x6 boards for practice, assuming a steep learning curve. Not. I have recently bought a Porter-Cable Dovetail Jig. The manual states that the jig depth measure should be set 3/8 inch below the template (in its lowest position). I [ ]  I have recently bought a Porter-Cable Dovetail Jig. The manual states that the jig depth measure should be set 3/8 inch below the template (in its lowest position). I can’t understand this as the template is approx. 1/4 inch thick and I would have expected the depth measure should be set to around 1/4 inch to compensate for the thickness of the template. Dovetail Jig Set. Thus, a dovetail jig is certainly very helpful for porter cable router jig youtube and accurate cutting of tenons and mortises with a wood router. Go to Home Page. Leave a comment as or Logout. My Account. There are lots of different dovetail joints. Once mastered, a good dovetail jig can make the process of creating properly fitting pins and tails a nearly foolproof endeavor.

Moreover, we used two height-adjustable locking bolts, which serve as templates for fast setting the cutting depth. For example, setting one of the bolts for cutting half-blind joints and the other for through joints, you can adjust the cutter overhang without using a ruler every time.

The bars feature only two rubber pads hence the jig can hold only two workpieces at a time and we deem it a shortcoming. If you have a workroom, it's very advisable to keep it clean. This jig is equipped with a port to connect a vacuum cleaner for removing dust and chips from your workplace.

User Manual Manufacturer. The Leigh has been making jigs and router accessories for 35 years and dovetail jigs are among its major line of products. For our review, we chose the Leigh Super 12" dovetail joint jig.

The 18" and 24" versions are also available for more mass production-oriented projects. Starting from the jig's base, it consists of two profiles made of aircraft-grade aluminum.

The cam action clamps are located on the top front area of the base with the two brackets for templates placed near the clamps. As a useful addition, the jig features the scale on the left side that allows positioning the template with a very high precision.

The jig itself attaches to the worktop with four screws. Hence, choosing this tool you can be sure you get yourself covered in terms of accessories. Also, the supply package contains nylon stop rod stops, the pull-out reference card, and the template with adjustable fingers, which we will describe further on.

The availability of the template with adjustable one-piece fingers is the main benefit of using this dovetail tool. The whole point is that each finger can be easily set to any position across the template for cutting joints according to various patterns including many unique ones.

Even more to that, with the jig, you are capable of moving the finger assembly back and forth along the scale on the left.

Therefore, by moving the fingers you can change the shape of pins and tails cut, making the joints narrower or wider. To be more specific, here are some numbers. In addition to the above-mentioned joints, the Leigh Super enables you to make sliding dovetails and half-blind dovetail joints. However, you need to keep in mind that the fingers adjustment may be pretty laborious as long workpieces require positioning of several fingers.

The very handy feature of the jig is its ability to process workpieces with up to 12" width. This means that in most cases you won't have to cut a workpiece to fit the tool but instead adjust the jig to the piece for an even joints distribution. The design of the Leight Super allows placing workpieces across the clamps, whether it's a single inch wide piece or three 4-inch ones. To facilitate the tool operation more, it has a non-slip clamping surface for a secure workpiece grip.

Another plus of the tool is that it makes cutting half-blind dovetails in a single pass. Such joints are the most widely used ones in making drawers, which are typical for dressers, for example, as they provide Porter Cable Router Jig 70 no visible connections on the front. In our opinion, this Leigh dovetail jig is aimed more at experienced joiners that seek a high cutting accuracy and enhanced tool adjustability.

Nevertheless, the detailed guide on the DVD included ensures an easy start even for beginning carpenters. If you wish to avoid marring your work table, you can screw the jig to a board and fasten it to the table with a vise. In practice, the model is the extension designed for router tables and table saws.

The jigs of another type stay fixed while the router is moved along their edges, this jig on the contrary mounts on a workpiece and moves along the pattern while the router remains still. Moving further to the design, we would like to highlight the aluminum bar that holds the guide underneath.

This guide provides a smooth movement of the jig in the miter slot. This woodworking equipment provides workpiece fastening with a wooden vice. Apart from the guide, the jig package includes front and rear blade guards, the MDF fence to support a workpiece, and plastic shield.

Considering the design of this dovetail tool, we were not surprised that it allows making only finger joints that are common for cabinets. The jig operation is quite easy, so using it is not a problem even for a beginner. Still, taking the initial measurements and setting the miter bar correctly is the most complex task when using the tool. The bar features two ledges that can be adjusted by moving closer or away from each other depending on the cut width.

With that, the distance from the closest ledge to the blade is to be the same. The ledges are adjusted with red and silver knobs located on the side of the jig base. As for the usability of this dovetail jig, it is impossible not to note its quick and easy installation. To use the tool you won't have to drill holes in the table or pick a vise.

It is enough to place the miter bar into the slot. The greatest thing about this jig is that it can be installed on a router table or a table saw. Thus, if you have the latter, you'll be able to cut workpieces and make joints right on the spot. Convenient, isn't it? The jig also features the sturdy acrylic deflector shield mounted on the front blade guard to keep your eyes safe from wood chips and particles.

However, as any equipment, the jig has some downsides. In our opinion, the dovetailing is a bit uncomfortable as a workpiece requires loosening and securing again after each pass. Nevertheless, this drawback is trivial considering that the INCRA model is designed for beginners and persons practicing an occasional cutting template use. Hence, this dovetail joint jig is a splendid choice for small workshops featuring router tables or table saws.

Picking this jig, you won't have troubles with installing it as the model is bidirectional and can be mounted on either left or right saws. Rockler is a large company evolved from a small family business of woodworking equipment supply that was founded by Norton Rockler in As one can see, this is a compact tool for router tables only.

The peculiarity of the tool is that its MDF platform features the oval opening that suits only for a router bit but not for a saw blade. The platform features two big clamps for the structure secure locking into a miter slot. There are 3 grooves on the platform, two for moving the backer sled, and one for placement of indexing keys. This dovetail router jig comes with 3 aluminum indexing keys to be installed into corresponding platform slots.

After completing this procedure, you'll be capable of getting equally spaced pins and recesses. In a similar way, you can change the size of the joints cut by adjusting the distance between the bit and key or selecting a different bit.

This model is one of the simplest to use box joint jigs. It can be installed on a router table within a minute and offers a super easy adjustment of the cutting depth. With such compact size, the model allows the use even with a small table and can be kept in a tool cabinet or under a table.

The distinguishing feature of the Box Joint Jig design is two holes in the platform for attaching the device to a board. Before getting started with the cutting, you need to make a hole for the router bit and sled in the board.

And that are all the preparations for making through and tight-fitting finger joints. As you can see, using this dovetail tool is one of the easiest ways for cutting box joints with the jig fit for beginning carpenters and wood crafting amateurs. Operating a router, you risk harming your ear due to a noisy workflow. Thus, don't forget to use personal protective equipment like hearing protectors. This model has somewhat uncommon design and can be used on router tables as well as standalone routers.

The jig is made of aluminum and is designed with 4 clamps for securing workpieces in place. Let us take a closer look at the way pieces are to be secured on the tool. When a router table is in use, you need to clamp the workpiece to the jig and do the cutting of recesses by moving the structure along the router's bit.

If you have a router only, the procedure is a bit more complicated. First, you need to secure a piece to the workbench with screw clamps, and then attach the jig to the piece. Item Write a Review. Add to Wish List. More Details.

View Full Details. Compare With Quick View Item Quick View Item 09B Quick View Item 03E Quick View Item Details Videos. Details This easy-to-use and accurate Premium Straight Edge Guide for Porter Cable routers is designed for models , , , , , , and Learn More. Customer Care Talk to a friendly customer care representative to help with your purchase. Talk to an Expert Get advice on the latest products and help with your projects. Sign Up. Connect With Woodcraft.

Resin Casting. Shop Talk. Woodcraft Magazine. Woodworking Adventures. Toledo Woodcraft franchise owner, John Nystrom. Carl Kuhnle. Part 3 : A bit about Carl: Carl is a retired attorney, and has been making his own furniture designs with influence of the Shaker and Mission styles, and has done commission work. His favorite tools are his router table, Tormek sharpening system, and thickness sander for panel work.

He enjoys designing and building jigs to speed up production, and for safety issues. Carl is looking forward to sharing his experiences as part of the Toledo Woodcraft Team with other woodworkers, teaching some classes regarding furniture design, designing, building, using jigs and basic power tools. Related Products Quick View Item Quick View Item Quick View Item 15F Write Comment You must be logged in to write a comment. Learn More.

Customer Care Talk to a friendly customer care representative to help with your purchase. Talk to an Expert Get advice on the latest products and help with your projects.

Sign Up. Connect With Woodcraft.

Kreg Jig Replacement Parts 05 Do It Yourself Reclaimed Wood Wall Design Simple Toolbox Plans