Hello Cablee, Porter Cable offers a 5 inch pad with 5 holes that are elongated, so you can use 8 hole hook and loop paper. Can I get the entire bottom pieces the are held on to the bottom of the sander with 3 screws? Millions of Parts From Top Brands. Hope this helps, -WJA. Push the porter cable palm belt sander code of the disc nut through the center of the sanding disc.

Submit your question. Thank you for your question! Our experts will get back to you as soon as they can. Ask Another Question. Continue Shopping. Discussion is closed.

Question: Random Orbital Sander Jacks. Hi, I have a and I recall seeing years ago pads that were sold that would enable you to use the sander for polishing cars etc. They were 5" pads and I used them for applying rubbing compound for difficult paint problems and then later to apply and remove wax.

They worked great. But I've not been able to find them anywhere and the ones that I purchased years ago have all been used beyond their expected life. Please help me find where I can buy more of these. There for a while Porter Cable did provide the 5" pads you are describing. Unfortunately they no longer supply them. Question: , , Major Vibration ggbhunter. I have a small shop and have approx 8 to 10 of these. These sanders have treated us well and would rather fix than replace. I have had Porter Cable Palm Belt Sander Jacket them all apart and can't find the problem.

Any ideas? Hello ggbhunter, You may want to inspect the SV bearing that sits inside the pad support. This bearing has a tendency to pick up a lot of fine dust that will get inside the bearing and cause the vibration you are speaking of.

If you have the sanders completely torn down, I would also check the armature bearings. Hello Gustav, Porter Cable offers a 5 inch pad with 5 holes that are elongated, so you can use 8 hole hook and loop paper. And it works surprisingly well. It is part number Hope this helps, -WJA.

Question: Fixed Pulley Hi, No the fixed pulley does not rotate. The fixed pulley and belt act as a break to creat a cross hatch pattern when sanding. The pulley will wear in time. Replace your fixed pulley and belt and you should be fine. Hope that helps. Good luck. The 8 hole discs are easier to find locally in the finer grit.

Hello , Porter-Cable does offer a pad that has 5 holes, but the way they manufacture it it can Porter Cable Palm Belt Sander Zip Code be used for 8 hole paper also. It looks like it won't work, but it works great. Hi WJA, Thanks for the info. I'm going to give this pad a try. Thanks, Buy the solid disc here or on eBay and then simply drill out the 8-holes with a drill press or what not using an 8-hole sanding disc as the template.

I have done this and it works fine. Hello scottshort, You are correct. Part number is the part that is used in the video. Thank you for your suggestion on mentioning part numbers in the videos. I will pass it on. I was cleaning my sander that the belt is very loose.

This causes the pad to spin very fast. I want to replace the belt but I'm wondering if the bearing should be free to spin? Hello sam, If your pad is spinning at a high rate of speed you are correct in replacing the belt. If the bearing, part number SV, in the pad support is hard to turn or is rough when it turns, now is a great time to replace it. Hi great video! In fact I didn't even know my belt was missing.

But your video calls this belt a "clutch belt" while on the parts list, I can't find it. One listed is called "main drive" or something like that which gives me pause Vibration caused by the operating action of this. Dust and grit containing metal particles.

Such preven-. High tool rpm caused by a worn out CFS. An extension cord must have adequate wire size AwG or American wire Gauge for safety. The smaller the gauge number of the wire, the greater the capacity of the cable, that is 16 gauge. An undersized cord will cause a drop in line voltage resulting in. When using more than one extension to make up the total length, be.

The following table shows. If in doubt, use the. The smaller the gauge number, the heavier the cord. Under some conditions and duration of use, noise from this product may contribute to. Some examples of these chemicals are:. Your risk from these exposures varies, depending on how often you do this type of work. Direct particles away from face and body.

The label on your tool may include the following symbols. The symbols and their definitions are as. Use of dust collection can reduce dust-. Use the correct power tool for your application. The correct. Any power tool that. Power tools are dan-. If damaged,. Many accidents are caused by poorly maintained.

Properly maintained cutting tools with sharp cutting. Use of the. This will ensure that the safety of the power tool is maintained. Contact with a "live" wire will make exposed. Dispose of coated dust particles according to the finish. Remove coated. The accumulation of fine sanding dust particles may self. Use gloves to provide extra cushion,. Sanding of these materials should only be performed. Always disconnect the sander from the power source before cleaning.

Always wear safety. Always use eye protection. All users and bystanders must wear eye protection that. Everyday eyeglasses are NOT safety glasses. Also use. Some dust created by power sanding, sawing, grinding, drilling, and other construction. Allowing dust to get into your mouth, eyes, or lay on the skin may promote absorption. Class I Construction.

Class II Construction. The greatest danger of lead poisoning is to children and pregnant women. Since it is difficult to identify whether or not a paint contains lead without a chemical analysis, we.

No children or pregnant women should enter the work area where the paint sanding is being. A dust mask or respirator should be worn by all persons entering the work area.

Best Bench Players In Nba 2021 Game Wood Carving Magazines Pdf Youtube Sanding Discs For Wood Lathe 6th