The galvanized trash can will "oil can" a little bit when it gets bogged down, but it pops right back when you turn the vacuum off. Works good just need to make sure you have a good colector, air tight. Oneida cyclone dust collector for sale 2020 just started carving a large piece of lime stone, and the cyclone did as advertized! The trash can is a plus over a 5 gal bucket as it needs less emptying which gives me more time working cleanly. The top had its own rubber seal which definately helps keep the suction in check. The dust deputy works as well as advertised but just like many others have said that's a lot of money for some molded plastic. I finally settled on flexible plumping couplings and it oneida cyclone dust collector for sale 2020 working very well.

Say your money and build your own collector!!!! I bought this and followed the installation instructions for a standard 5 gallon bucket and lid. The wheels add mobility and the extra weight adds stability.

Now I can leave the shop vac in the corner and roll this around from station to station. Much simpler, quieter, and fewer filters used. It's payed for itself already in under a year. Mounted the unit on a piece of scrap AC plywood, cut to fit inside a 31 gallon galvanized trash can. Used an old serpentine belt from the Jeep glued to the plywood as a sealing gasket, grooved edge out, towards the can. Made a gasket from gasket stock for differentials to go between the plywood and the Deputy.

Sealed on the plywood side with RTV sealant. Works perfectly! The galvanized trash can will "oil can" a little bit when it gets bogged down, but it pops right back when you turn the vacuum off.

No more shoveling shavings after a planing session! Many people have mounted the DD to a table top. The way I found to do it was to get a second bucket and screw that to the wood box I built to encase my shop vac and lessen the noise.

After you have a mobile and strong surface, insert the DD into the second bucket and you no longer have to worry about it tipping over, provided that your table is stable. This is not for the heavy duty user - it is too small. But it is excellent for folk's like me with a small shop with only one machine hooked up at a time with only a simple shop vacuum of some sort I use a little 5 gal ShopVac. Everything goes through the Dust Deputy and very little ever gets to the ShopVac.

It takes the big stuff, the small stuff and just fills up the plastic paint bucket. I built mine into a 'tower' with wheels and the ShopVac on the top. Move it around and connect the hose. It is a bit difficult pulling the pail out to empty it and I am still working on a fool proof way to keep the hoses on the input side slippery plastic but other than that, I am a happy camper.

This Dust Deputy is wonderful. I works great to keep my shop cleaner. It eliminates the need to frequently clean the filter in the shop vac. I can work all day and only need to dump the contents once a day. Love Love Love Great value at bargain price - I was dubious, but bought a 5 gal pail and top at my big box store, hooked it up in 2 minutes and was completely surprised with the improvement in my shop vac suction without a clogged filter anymore.

Just make a 3 to 3. Hooked it in to my planer and it was very impressive seeing its vortex action. I am planning a combo cart to house it with the vac because it readily tips over.

My workaround was putting a drill press vice about 5 lbs and heaviest small item I could do without for awhile into the pail, so that it now strands up to the hose movement without tipping.

Removed over sf of tile and thinset. The DD captured all the chips and dust with barely any dust in the vacuum. Had a pro use it when he ground the surface smooth- he was so impressed he charged me half if I would give him the DD setup. Everyone who saw it in action now wants one, including the new-floor installers.

Works good just need to make sure you have a good seal, air tight. As far as I can tell, This unit uses the same cyclone geometry as one that I've built. Mine cost me approx. What a great device. I make powder horns and belt sand them with a 60 grit and grit belt. After 6 horns, the shop vac filter is totally clogged. I used the Cyclone for the month of March and when I cleaned the shop vac filter at the end of the month, it looked like I had only used it on one or two horns.

This is great, wish I would have bought one of these years ago. It was pretty easy to mount it to a metal can I already had. Spent more time going to the hardware store to purchase bolts and silicone than actually putting it together.

Great item, wholeheartedly recommend. I love this device. It works great, but I've had to epoxy it back together twice. Fix that and it will be dynamite! Like all small cyclones, this one is only for use with low-power 2 and less hp vacuums.

Any more powerful unit will simply suck the dust from the inlet port straight to the outlet port, and you'll still end up with all the dust in your shop vac and its filter. I easily attached the dust cylclone to a 35 gallon plastic container and I bought the shop vac brand hoses 2.

The cyclone was sealed to the container lid with permatec silicone sealent and the rest is history. I wish I had bought this soonerand I will be buying another one in the future. Also there was no perceivable dust getting to my shop vac. The dust-deputy does remove most of the dust particles before they reach the dust collector.

The plastic is heavy enough to support the vucuum even when the lines are blocked. It does have some distortions in the plastic base from mass production, but these did level out once bolted down to a plywood top, but may not if using a simple plastic lid. Be sure you plan on building a heavy base or attaching everything to the dust collector.

The device and bucket are so light that the weight of the hoses will cause it to tip over frequently if you do not. I have the DD hooked to a small shop vacuum. It is so efficent that a new filter in the shop vac still looks new after several uses. The ports are tapered to allow various size hoses to be used.

I wish that Oneida would include the copper grounding tape with even the basic DD as that would make grounding it easier. Still a great product!

I built one of the carts I saw on Woodsmith Shop to hold my shop vac and the dust deputy. I also added a vacuum switch because I knew if it wasn't automatic, I wouldn't use it. The cart and the vacuum switch work great. I should have less cleanup to do in the garage. This product goes between the source of dust and your shop vac.

It is my poor-man's version of a stationary shop dust collection system. I attach it to my power tools and use it to vacuum my shop floor. This product does what is to me an amazing job of collecting dust.

I keep looking inside my shop vac for dust and it takes a close inspection to see any there. Before adding this product, my shop vac filter would quickly clog up, necessitating removal of the filter and a messy cleaning of the dust from the filter. With such an efficient particle trapping filter, I would have needed to clean the filter even more frequently to keep up the suction.

But with the cyclone, I can go a very long time between filter cleanings. Even then, there is barely any dust on the filter.

When the cyclone is attached to a collection bucket such as a 5-gallon paint or drywall container, it is a bit top-heavy. You need to attach it to your shop vac by some means if you want the cyclone roll around with your vac.

The manufacturer has some suggested ways to do this such as with a bungee cord or by an auxiliary platform. I highly recommend this product. I mounted it on a 10 gal metal bucket with a bead of chalk between it and the lid, works great.

I'm sure a more air tight plastic bucket would be even better. I'm an brazilian user. The oneida was what I needed. There are good videos about this product that are helpful. I installed it on a "big box" 5 gallon bucket and use my shop vac for suction. The cyclone works, the shop vac is completely empty. The cyclone is easy to install,works as stated.

I bought a Rigid shop vac and installed the cyclone. The vac was new,never seen dust. It still has't!! That is how well the cyclone works. If you want to control the dust in your shop get the cyclone. I used to be stingy about using my festool shop vac for anything other than collecting dust from my sanders, because I didn't want to fill up the bag.

Now I don't have to be. But best of all, with the bag not choking up with dust, I have far better suction. I attached it to a 5 gallon bucket with a wooden spacer and some caulk.

It's very effective at keeping most of the sawdust out of the shop vac filter. The plastic bucket tends to tip over, but I'm going to fix that by putting an old brake disk in the bottom. The capacity of this unit is insufficient for the amount of sawdust I generate.

The unit is too small in diameter and too short to effectively remove dust from the air. Static electricity buildup also prevents dust from falling into catch bin, resulting in significant blow-by to my vacuum cleaner.

I bought a dust deputy. The unit has no gasket and the local store said that I would have to make my own gasket, they do not have any. I bought I guess when you buy a car the tires might be extra, you need to check witch model you are buying it my not come with them. Part of my garage woodworking shop dust collection. I use it on my cnc machine to avoid dust in the workshop. I put 4 wheels on my 5 gallon bucket, I had to change the wheels location cause it's top heavy.

I've been using this for close to a year now in my shop connected to various power tools. Consequently, the filter on my shop vac stills gets clogged up pretty quick, just like before, with the fine stuff. This is after clogging filter after filter when using it without the dust deputy.

Great product. Nice unit for seperating big stuff before shop vac. Saves the expensive shop vac HEPA filter. Wish it was bigger and took 4 inch hoses. I built my own dust collector using the Dust Deputy.

It does everything as advertised. I am happy with the product. I am in the process of doing up a small workshop and I plan to use the cyclone with a shop vac as well as the second stage filter after thein in a fixed system.

Tests to date have been spectacular. Once mounted, this contraption works like a Dyson vac to spool away all the dust and debris from the tool into the bucket below. I saw it on a few online videos, and the thing seemed to work well. In real life with a shop vac, it really does work well! Virtually nothing ended up in the shop vac. I've planed a bunch of boards and there's still nothing in the shop vac.

I ran it with the jointer, nothing in the vac. I chewed through some dusty fir on the table saw, nothing in the vac. I cleaned up the work area afterward, still nothing. A couple nagging issues that I can get over pretty easy. I would have liked to receive a gasket with the DIY kit.

As it was, I just used some gasket maker goop, works well The port that connects to the shop vac didn't really fit my particular shop vac A Shop Vac very well. So I wrapped the spout in blue tape and it fits snug now. A little more taper on this spout would have solved it. The dust Oneida 15 Hp Cyclone Dust Collector For deputy works as well as advertised but just like many others have said that's a lot of money for some molded plastic.

The molded plastic unit I received is not flat on the bottom so silicone was necessary, especially when trying to fit it to plywood even with a gasket. In as much as I probably spent just as much with the DIY as I would have with the whole kit I think I have a better finished product by buying higher quality materials than what others have said comes with the deluxe version.

Plus it's customized for my purposes which is what so many seem to have done regardless. Good product, overpriced, not real high quality plastic so be careful with it. I am very happy to have it connected to my shop vacuum to save my bags. It is pleasant to see the cyclone in action to know it is working.

I did have some problems connecting the hoses. The fittings seemes an odd size as compared to the vacuum and hoses I have. Brand Oneida Air Systems. Harvey Supply. Featured Sale. Types Single Stage. Two Stage. Product Cyclone Separator.

Dust Collector. Dust System Accessories. Air Flow - CFM. Less Than CFM. Hp 3 HP. Size 32 gal. Show More. Style Two Stage. Bag Filter. Ships From Woodcraft. Oneida Air Systems. Dust Collection. Single Stage Dust Collectors. Two Stage Dust Collectors. Cyclone Dust Collectors. Prev 1 2 3 Next. Compare Items:. Filter Results.

Manual Wood Saw Zero K J Custom Lumber Products Uk