- : Customer reviews: Kreg Tool K5 Master System

For your convenience, this post contains affiliate links to supplies or tools I used to complete this project. Purchases made using these links help support the Saws on Skates website and allow me to share more DIY projects.

There is kreg pocket hole system review error cost to you for using these links. Click here to visit kreg pocket hole system review error site policies.

We can experience pocket hole problems no matter what brand of pocket hole jig we use. The Kreg Jig uses preset holes to drill angled pocket holes in a piece of wood.

A pocket screw, specifically designed for use with pocket holes draws the two pieces of wood together to form a strong joint. Step 1 — Set the Drill Guide The first step to using the Kreg Kreg pocket hole system review error is to adjust the drill guide to the thickness of your board.

Step 2 — Set the Drill The next step is to set the drill depth. Step 3 — Drill Pocket Holes Next clamp the board in the jig to correspond with the appropriate drill holes. Chuck the drill bit in your drill and insert the drill bit into the guide block until it hits the wood. Slightly raise the drill bit and bring the drill up to full speed. Then gently lower the bit into the wood and start drilling the pocket hole.

Keep drilling until the collar on the drill bit contacts the drill guide. A butt joint joins the end of kreg pocket hole system review error piece of wood to the edge of another piece of wood.

Common uses for butt joints are frames for side assemblies and doors. An edge joint joins the edges of two boards. Common uses for edge joints are panels and table tops. Pocket holes need to be drilled into the ends of a board when creating butt joints. We need to drill the pocket holes into the vertical blue pieces not the horizontal wood grain pieces.

The grain of wood runs the length of the board. The end of the board is referred to as the end grain. Think of the wood grain or wood fibers like a box of drinking straws. Imagine driving a screw into the end of a box of drinking straws.

What would happen to the screw? Driving screws into end grain does not create a strong joint. When edge joining the pocket screw is driven through the edge of the wood and this makes a strong joint.

Many furniture projects use different thicknesses of wood. Not Good! And yes, I have done this on more than one occasion! How can you prevent this pocket hole mistake from happening?

Exposed screws are not an attractive look for DIY furniture! I use my Kreg Jig to drill pocket holes for nearly every furniture project I build. It only makes sense eventually the drill bit would become worn. With a crisp, clean pocket hole you can place the plug in the pocket hole, sand the plug flush with the surrounding wood and the pocket hole will virtually disappear.

With a jagged pocket hole you can place the plug in the pocket hole, sand the plug flush with the surrounding wood, but edges of the pocket hole will still appear jagged. When a pocket screw is driven through an angled pocket hole it draws the two pieces of wood together tightly. Wood is a living thing. Wait, did I just say wood is a living thing?! Well, not exactly living, but it is hygroscopic. Simply put, hygroscopic means it absorbs moisture from the air.

Wood is constantly absorbing and giving off moisture, just as it would when it was alive. Remember earlier how I described wood like a box of drinking straws. When the drinking straws, ummm woodfills with moisture it swells and gets bigger. When it loses moisture it shrinks and gets smaller. The top looked great in the summer, but in the cooler months the joints of the top just ever so slightly pulled away from each other.

And the edge of one of the pieces even started to slightly curl up. Can you stop wood movement? The short answer is kreg pocket hole system review error, but you can help reduce some of these issues by gluing the joints. Almost all of us have had a finish ruined by glue squeeze out. The glue squeezed out, we stained the piece and the glue prevented the stain from soaking into the wood.

This glue creates a strong bond and is stainable. By now we know how a pocket hole joint works. A pocket screw is driven through an angled pocket hole, and the screw draws the two pieces of wood tightly together.

Despite this, you still need to use clamps to properly align the joint before attaching it the joint with pocket screws. Nothing beats the mechanical advantage of a clamp. Your pocket hole joints will stay in place, the joints will fit better and your furniture projects will look more professional.

This way I can layout the entire assembly, get all of the joints the way I want them, tighten the clamps and attach with pocket screws. Use clamps when you assemble your pocket hole joints, and the look of your projects will go from amateur to professional. Pocket screws are specifically designed to work with pocket holes.

Pocket screws have threads only on the lower portion, while the upper portion, or shank is not threaded. This design allows the shank of the pocket screw to slide through the pocket hole and pull the joint tight together. Unlike pocket screwswood screws have threads along the entire length of the shank. Wood screws may not pull the boards together resulting in a loose-fitting joint.

Worse yet wood screws may crack the board. Use only Kreg kreg pocket hole system review error pocket screws or another authentic pocket screw by another brand to create a tight pocket hole joint.

Pocket screws are available in coarse thread and a fine thread. Use coarse thread pocket screws for softwoods like pine, plywood, particle board and Kreg pocket hole system review error. Use fine thread pocket screws for hardwoods like oak, maple, hickory, cherry, walnut and birch. Always use the correct length pocket screw for the pocket hole you have drilled. Tip: When I use different length screws for a furniture project I will sometimes write lightly in pencil next to the pocket the length of screw I need to use.

Kreg pocket hole system review error we discussed earlier pocket screws are different than wood screws, and that means we have to take a different approach when driving them into the workpieces. Basically we want to stop driving the pocket screw when we start feeling some resistance. Overtightening a pocket screw can strip the pocket hole which can create a loose joint. Overtightening could even drive the screw through the other workpiece.

I set the clutch on my drill to avoid overtightening pocket screws. Setting the clutch prevents the drill from driving the screw any further when the drill meets a certain amount of resistance. This prevents over tightening and stripping the pocket hole. I recommend using a drill for both drilling pocket holes and driving the screws rather than an impact driver. The impact action of an impact driver can loosen the drill bit depth collar when drilling pocket holes and could possibly strip the the pocket hole when driving the screw.

Tip: Over tightening a pocket screw is just one way a pocket hole can become stripped. Kreg pocket hole system review error way a pocket hole can become stripped is if you remove a pocket screw and then reattach it. Fixing a stripped pocket hole is as easy as grabbing some wood glue and heading to the kitchen for some toothpicks. The plug cutter makes plugs to fill pocket holes.

The kreg pocket hole system review error are cut from leftover scrap wood from your project, so the plugs will exactly match the wood color and wood grain of your project. The plugs are glued into the pocket holes and then sanded flush. Check out my plug cutter setup tips and video!

It will happen to all of us at some point. What do we do now? You need my secret weapon I keep in my tool arsenal for hard-to-reach pocket holes — a right angle attachment!

The guide includes all of the useful tips in this post plus much more! Tell me about it kreg pocket hole system review error the comments. Oh, and if you found this helpful, would you please pin it to Pinterest? Thank you — Scott. Hi James — There are a couple of ways to tackle these round corners. You could square the round corners with a chisel.

Or you can use a specially made corner chisel like this one to square the corners. Very helpful, thanks for this information. Winter came along with terrible dryness, and guess what?

Feb 12,  · Kreg Pocket Hole Jigs Build Pocket Hole Projects Faster and Smarter. Kreg has a rich history of helping woodworkers achieve super clean finishes with minimal fuss. Now, the brand has announced its latest innovation in pocket hole joinery. Kreg has designed the and Pro Pocket Hole Jigs with all the tools to take your woodworking to the. Aug 05,  · A bit of trial and error but once you get it and don't mix and match plywood you're good to go. Then you discover things aren't going quite right. The screws are poking through the joined piece pocket holes are too deep. On the older K4 the depth setting /5. Mar 30,  · Pocket Hole Plugs; Screw Starter Kit; Setting Up the Kreg Jig K4 Pocket Hole System. The Kreg Jig K4 itself is small but mighty, made of glass-filled nylon. The simplicity of its design belies its usefulness – the device that can easily fit on the corner of a workbench really allows a world of new projects, repairs, and improvements/

Are Timber Wolf Blades Good Day Bevel Up Jointer Plane Line Rockler T Track Router Bit 8bit