If you try to apply the second coat while the first coat is still wet, you are going to strip away at the first coat. It has to be high quality so do not cut corners by using a cheap brand. And while I did have some evidence that this hack could serve my own needs, I was still a bit concerned that it may not have the same effect on gep aged, not to mention paintedwooden door. Obtain a feel for the staining process by picking a small, flat area on the fierglass to practice. A tutorial from Rachael of Lovely Crafted Home gave me major hope, when she successfully gel stained her fiberglass front door to make it look gel coat stain fiberglass doors english a legit, wood door. The idea behind these stains is that they add a layer of color gel coat stain fiberglass doors english a wood eglish so that the natural grain can still be seen.

Mixing and Tinting Custom colors can be achieved by intermixing colors or by adding up to 10 ounces of universal or industrial colorant per gallon. The amount of colorant added may affect its performance and extend dry time. Stir for uniform consistency.

Coverage: Approximately 1, to 1, square feet per gallon. If the wood is finely sanded or nonporous, coverage is approximately to 1, square feet per gallon.

If the surface is porous, coverage is approximately to square feet per gallon. Coverage will vary significantly depending on application method and condition of wood. Drying Time Approximately 6 to 8 hours depending upon temperature, humidity, air movement, and the amount of stain on the surface.

For additional color depth, a second coat of stain can be applied after 8 hours. Dry time may also be extended due to excess stain application or lack of stain Gel Coat Stain Fiberglass Doors Video penetration. Cleanup Using a cleaning solvent, such as paint thinner or mineral spirits, is recommended for cleanup. The use of paint thinners or mineral spirits may violate VOC compliancy in your area. Check with your Gel Coat Stain Fiberglass Doors Quote local government agencies to ensure proper compliancy.

However, this stain can be top coated with most clears. If a lacquer topcoat is desired, test for compatibility before using. When applying water-based finishes, allow a minimum of 24 hours before top coating. Old Masters uses only the finest ingredients to create the highest quality stains available today.

Old Masters stains can be used to:. Stain Scrap test piece Stir stick Drop cloth Bristle brush, synthetic brush, foam brush applicator, cheese cloth, or rags Lint-free cloth Mineral spirits or paint thinner Rubber gloves.

Gel Stain. Available colors:. Aged Oak. American Walnut. Carbon Black. Crimson Fire. Dark Mahogany. Dark Walnut. Early American. Golden Oak. Natural Walnut. Pickling White. Red Mahogany. Rich Mahogany.

Spanish Oak. Special Walnut. Vintage Burgundy. Weathered Wood. DANGER: Rags, steel wool, sanding residue, and other wastes used or soaked with this product may spontaneously catch fire if improperly discarded. When recoating, allow a minimum of hours, depending on drying conditions.

Low temperatures and high humidity will increase drying time. DANGER: Rags, steel wool, sanding residue, and other wastes used or soaked with oil-based products may spontaneously catch fire if improperly discarded. No ignition source is required for these wastes to start on fire by themselves. Immediately place rags, steel wool, sanding residue, and other wastes used or soaked with these products in a sealed, water-filled metal container. Dispose of in accordance with local fire regulations.

Fiberglass Doors Staining Guide. Posted on November 6, Products used:. Additional Supplies. Phillips screwdriver Masking tape and paper Hammer Saw horses padded Extra cleaning rags Putty knife Utility knife These instructions are designed for use on all fiberglass, carbonite, composition, and other simulated wood grain surfaces, as well as stainable door frames. Before You Begin. A Few Basics Thoroughly read and follow all the instructions as printed in this brochure and carefully read through product labels.

Review suggested supplies on the back page and gather additional supplies. Provide a good working environment, one that is free of dust and has adequate lighting and ventilation.

Ventilation is important in the application of stains and finishes. Please read product cautions carefully. Remove the door from its hinges and place on flat padded saw horses or substitute supports.

Remove all hardware hinges, doorknobs, locks, and weather stripping. Trim or scrape the factory sealant that has seeped out between window trim and the glass, if applicable. Mask off any glass and weather stripping that was unable to be removed as well as the doorjamb. Using one of your extra cleanup rags, wipe the entire surface with either the provided mineral spirits, or an all purpose cleaner.

Wipe clean Gel Coat Stain Fiberglass Doors China and allow to dry thoroughly. Stir the stain well. Obtain a feel for the staining process by picking a small, flat area on the door to practice. Apply stain liberally in this small area with Gel Coat Stain Fiberglass Doors Australia the sponge brush and remove excess stain gradually until the depth of color is satisfactory.

When finished practicing, remove the stain in this test area with the provided mineral spirits and extra cleanup rags. Staining Sequence. Stain all door panels following the order indicated on this diagram.

Best Rap Hip Hop Songs All Time Rikon Belt Disc Sander Youtube