Support | DEWALT

Denotes risk of electric shock. Technical data Voltage U. Weight Fuses: Europe U. Take appropriate measures for the protection of hearing if the sound pressure of 85 dB A is exceeded. The following symbols are used throughout this manual: Denotes risk of personal injury, loss of life or damage to the tool in case of nonobservance of the instructions in this manual.

Read the following safety instructions before attempting to operate this product. Keep these instructions in a safe place! General 1 Keep work area clean Cluttered areas and benches can cause accidents.

Keep work area well lit. Do not use Power Tools in the presence of inflammable liquids or gases. For use under extreme conditions e. Supervision is required for those under 16 years dewalt router sign making unit age.

They can be caught in moving parts. Preferably wear rubber gloves and non-slip footwear when working outdoors. Wear protective hair covering to keep long hair out of the way. It is safer and it frees both hands to operate the tool. Be sure that the switch is released when plugging in.

Use common sense. Do not operate the tool when you are tired. Unplug the tool when not in use, before servicing or changing accessories. Do not force small tools or attachments to do the job of a heavy-duty tool. The tool will do the job better and safer at the rate for which it was intended. The use of any accessory or attachment or performance of any operation with this tool, other than those recommended in this instruction manual may present a risk of personal injury.

Keep the cord away from heat, oil and sharp edges. Follow the instructions for maintenance and changing accessories. Inspect the extension cords periodically and replace them if damaged. Keep all controls dry, clean and free from oil and grease. Have damaged guards or other defective parts repaired or replaced as instructed.

Do not use the tool if the switch is defective. To avoid danger, electric appliances must only be repaired by qualified technicians. Additional safety rules for cutters Always use cutters with a shank diameter corresponding to the size of the collet installed in your tool. Always use cutters suitable for a speed of Never use cutters with a diameter exceeding the maximum diameter indicated in the technical data. Electrical safety The electric motor has been designed for one voltage only.

Always check that the power supply corresponds to the voltage on the rating plate. Package contents The package contains: 1 Dewalt router sign making unit 1 Parallel fence with fine adjustment and guide rods dewalt router sign making unit Spanner 22 1 Dust extraction adapter 1 Guide bush 1 Instruction manual 1 Exploded drawing Check for damage to the tool, parts or accessories which may have occurred during transport.

Take the time to thoroughly read and understand this manual prior to operation. Mains plug replacement U. Disconnect the plug from the supply. Cut off the plug and dispose of it safely; a plug with bared copper conductors is dangerous if engaged in a live socket outlet. Only fit 13 Amperes BSA approved plugs fitted with the correctly rated fuse 1.

The cable wire colours, or a letter, will be marked at the connection points of most good quality plugs. Attach the wires to their respective points in the plug see below. Before replacing the top cover of the mains plug ensure that the cable restraint 3 is holding the outer sheath of the cable firmly and that the two leads are correctly fixed at the terminal screws.

Description fig. Inserting and removing a cutter fig. B Press and hold down the spindle lock 4. Using the 22 mm wrench, loosen the collet nut 3 a few turns and insert a cutter Tighten the collet nut and release the spindle lock 4.

Never tighten the dewalt router sign making unit nut without a cutter in the collet. Replacing the collet fig. Other precision collets are also available to suit the cutter used. Separate the collet 25 from the collet nut 3 by pulling it firmly. Click the new collet in place. Setting the electronic speed control dial fig. A The speed is infinitely variable from 8, to 20, min-1 using the electronic speed control dial dewalt router sign making unit for uniform cutting results in all types of wood and plastics.

Turn the electronic speed control dial to the required level. The correct setting, however, is a matter of experience. A Your DEWALT Router is equipped with a high precision depth adjustment system including a revolver depth stop 20a measuring lens 12 and fine adjuster Quick adjustment fig.

Lower the router carriage until the cutter is in contact with the workpiece. Tighten the plunge lock 14 by pushing it down. Never use a light socket. Never connect the live L or neutral N wires to the earth pin marked E or. For V units with a power rating exceeding W, we recommend to fit a plug to BS standard.

Using an extension cable If an extension cable is required, use an approved extension cable suitable for the power input of this tool see technical data. The minimum dewalt router sign making unit size is 1. When using a cable reel, always unwind the cable completely. Also refer to the table below. Conductor size mm2 0. ENGLISH For optimum ease of operation, the carriage return can be adapted to the required depth of cut by rotating or sliding the knurled nut 9.

Loosen the clamping screw Rotate the handwheel 11 until the fine adjuster 17 touches the revolver depth stop Set the measuring lens to a round figure e. Adjust the depth of cut using the dewalt router sign making unit 11 and the measuring lens The distance between the top of the revolver depth stop and dewalt router sign making unit bottom of the dewalt router sign making unit adjuster is the adjusted depth of cut.

Tighten the clamping screw Triple depth adjustment using the revolver depth stop fig. E The revolver depth stop 20 can be used to set 3 different depths.

This is particularly useful for deep cuts, performed in steps. Place a depth template between the fine adjuster 17 and the revolver depth stop 20 to adjust the exact cutting depth. If required, set all three screws.

For installing the Router in inverted position, refer to the relevant instruction manual on the stationary tool. Fitting the parallel fence fig. Slide dewalt router sign making unit parallel fence 19 over the rods. Tighten the locking bolts 5 temporarily. Adjusting the parallel fence fig.

Tighten the plunge lock 14 Dewalt Router Sign Making Question and limit the carriage return using the knurled nut 9. Position the Router on the cutting line. Slide the parallel fence 19 against the workpiece and tighten the locking bolts 5. Adjust the parallel fence using the fine adjuster The outer cutting edge of the cutter must coincide with the cutting line.

If required, loosen the screws 28 holding the plastic guide strips 29 and adjust the strips to obtain the desired guiding length. Fitting the baseplate extension and trimming plate option fig. The trimming plate 30 is used for trimming of projecting glued edges. Fit the baseplate extension to the free end of the guide rods 6.

Guide the tool with one hand on the knob 23 and the other on the opposite grip For trimming projecting glued edges, fit the trimming plate 30 to the baseplate extension as shown in figure H. The trimming plate can be fitted directly next to the cutter and ensures optimim guidance.

AVID POWER Amp HP Compact Router with Fixed Base, 5 Trim Router Bits, Variable Speed, Edge Guide, Roller Guide and Dust Hood, Avid Power Makita RTCX7 /4 HP Compact Router . The planer weighs lbs. and operates off of the DEWALT Volt MAX battery system. Lightweight and cordless, the planer can be easily transported around the jobsite without the hassle of a cord. The DCPB is sold a bare tool. Keep your DEWALT Volt tools running longer with the Volt MAX Lithium-Ion Premium Battery Pack (DCB). GR 24" 5 HP Drum Sander Dual drum sanding to cut the work in half. You can't beat the GR 24" 5 HP Drum Sander for removing planer knife marks and glue lines after panel glue ups while maintaining a consistent board thickness. The 6" dual drums allow a coarse and fine sanding in one pass when desired. The GR features a single feed rate of 11 feet per minute.

Wood Work Cost In Hyderabad 50 Woodpecker Tools Ireland