dewalt radial arm saw parts for sale | eBay

Years of experience, thorough product development and innovation make DEWALT one of the most reliable partners for professional users. Dewalt 720 radial arm saw on appropriate measures for the protection of hearing if the sound pressure of 85 dB A is exceeded. Standard equipment: TCT blade, blade guard and tools, no-volt release switch. Fuses: Europe U. BM The following symbols are used throughout this manual: Denotes risk of personal injury, loss of life or damage to the tool in case of non-observance of the instructions in fewalt manual.

Safety instructions When using Power Tools, always observe the safety regulations applicable in your country to reduce the risk of fire, electric shock 72 personal injury. Read the following safety instructions before attempting to operate this product. Keep these instructions in a safe place! General 1 Keep work area clean Cluttered areas and benches can cause accidents.

Keep work area well lit. Do not use Power Tools in the presence of inflammable liquids or gases. For use under extreme conditions e.

Supervision is required for those under 16 years of age. They can be caught in moving parts. Preferably wear rubber gloves and non-slip footwear when working outdoors. Wear protective hair covering to keep long hair out of the way. It is safer and it frees both hands to operate the tool. Be sure that the switch is released when plugging in. Use common sense. Do not operate the tool when you are tired. Unplug dewalt 720 radial arm saw on tool when not in use, before servicing or changing accessories.

Do not force small tools or attachments to do the job of a heavy-duty tool. The tool will do dewalt 720 radial arm saw on job better and safer at the dewalt 720 radial arm saw on for which it was intended.

The use of any accessory or attachment or performance of any operation with this tool, other than those recommended in this instruction manual may present a risk of personal injury. Keep rdial cord away from heat, oil and sharp edges.

Follow the instructions for maintenance and changing accessories. Inspect the extension cords periodically and replace them if damaged. Keep all controls dry, clean and free from oil and grease. Check for misalignment and seizure of moving parts, breakage of parts and any other conditions that may affect its operation. Have damaged guards or other defective parts repaired or replaced as instructed.

Do not use the radal if the switch is defective. To avoid danger, electric appliances must only be repaired by qualified technicians. Dewakt safety rules for radial arm saws Protect the electric power supply with a suitable fuse or circuit breaker.

Keep the bearing tracks in the arm and the bearings on the roller head assembly dewalt 720 radial arm saw on and free from grease. Before switching ON, make sure that the fence is in the correct position. The blade should not contact the material until the saw is pulled by the handle.

When ripping, keep the riving knife adjusted to the correct distance from the blade 1 - 3 mm and make sure the kickback fingers are properly adjusted. When ripping, always check the direction of feed. Regularly agm the adjustments for accuracy and adjust as required.

Racial sure that the blade rotates in radal correct direction and that the teeth are pointing towards the fence. Make sure all dewalt 720 radial arm saw on handles are tight before starting operation. Never run the machine without all guards in place. When not in use, protect the saw blade completely using the blade guard.

When not in use, when changing blades afm carrying out maintenance, disconnect the machine from the power supply. Always use sharp blades of the correct type designed for the workpiece.

The recommended blade diameter raeial stated in the technical data. Do not wedge anything against the motor fan to hold the motor shaft. Do not force the cutting action. Stalling or partial stalling of the motor can cause major damage.

Allow the motor to reach full speed before cutting. Do not lift the machine by its worktable. Do not cut ferrous metals, non-ferrous metals or masonry. Do not apply lubricants to the blade when it is running. Do not place either hand in the blade area when the saw is connected to the power source. Do not reach around behind the saw blade when in use. Do not place hands closer than mm from the saw blade while cutting. Do not use damaged or saa saw blades.

Residual risks The following risks are inherent to the use of radial arm saws: In spite of the application of the relevant safety regulations and the implementation of safety devices, certain residual risks cannot be avoided.

These are: - Impairment of hearing. Take the time to thoroughly read dewalt 720 radial arm saw on understand this manual prior to operation. Electrical ln The electric dewalt 720 radial arm saw on has been designed for one voltage only.

Always check that the power supply corresponds to the voltage on the rating plate. Mains plug replacement U. Disconnect the plug from the supply.

Cut off the plug and dispose of it safely; a plug with bared copper conductors is dangerous if engaged in a live socket outlet. Only fit 13 Amperes BSA eadial plugs fitted with the correctly rated 7220 1. Sa cable wire colours, or a letter, will be marked at the connection points of most good quality plugs. Attach the wires to their respective points in the plug see below.

Before replacing dewalt 720 radial arm saw on top cover of the mains plug ensure that the cable restraint 3 is holding the outer sheath of the cable firmly and that the two leads are correctly fixed at the terminal dewalf. Description fig. This high precision machine can be easily and quickly set to crosscut, bevel, mitre, or rip. With the help of the wide variety of accessories, your Radial Arm Saw will perform virtually all workshop operations.

For optimum safety, all major controls have both a latch and a locking device. Also refer to the quick reference chart in this manual. Never connect the live L or neutral N wires to the earth pin marked E or. For V units with a power rating exceeding W, we recommend to fit a plug to BS standard. Using an extension cable If an extension cable is required, use an approved extension cable suitable for the power input of this machine see technical data.

The minimum conductor size is 1. When using a cable reel, always unwind the cable completely. Also refer to the table below. Cable rating Amperes 6 10 15 20 25 Cable length m 7. Assembly and adjustment Prior to assembly and adjustment always unplug the tool. For aarm performance of eadial saw, it is of vital importance to follow the procedures in amr paragraphs below. Unpacking your saw fig.

A1 Armm out the unit from the box. Lock the ddwalt using the mitre clamp lever Proceed with assembling the legstand. Legstand fig. Dedalt The legstand 30 consists of four legs 31four traverse rails 32 and four top traverse rails Dewalg latter are the same size as the base frame of your radial arm saw.

Assemble the legs and traverse rails as shown. Tighten the bolts. Secure the saw to the top. The saw table fig. E1 - Saaw Adjusting the table using the arbor fig. Turn the motor to vertical position and lock it using the bevel latch and the bevel clamp lever.

Release the qrm lock 15 fig. A2 and move the head to its fully forward position.

Jet 1221vs Uk Ukmt Woodcraft Pfeil Gouges Review