Pen Press. Brand Bessey. Woodworking Clamps and Vises. WoodRiver - 3" Clamping Squares 4 pc. Clamp On.

Designed for portability and space- saving, these vises have a clamp-on base for quick installation and removal from a benchtop. The base also swivels and can be locked in place. Vises with flat and V jaws also known as pipe jaws have a second set of jaws that securely grip pipe and other round objects. Hold your smallest workpieces with these vises, which have a clamp-on base for quick installation and removal from a benchtop.

The head tilts, rotates, and locks in place to hold work at an angle. Suction - mount vise attaches to smooth surfaces. Use the lever to engage and disengage the rubber suction pad.

For large workpieces, these vises open three times as wide as standard tilting-head vises. The head tilts, rotates, and locks in place to hold your work at an angle. Vises have one smooth jaw and one grooved jaw for clamping flat, round, and uneven workpieces.

The 5- lb. For temporary mounting, add a clamp - on base sold separately. Vise with self-centering jaws has jaws that move at the same time to keep parts in the center of the vise. Push the handle to slide the jaw into place for quicker setup than standard drill-press vises. Mount these vises directly to your drill press for drilling, tapping, and reaming applications.

Use the step on the jaws to raise the workpiece and allow more clearance for cutting tools. Lever - locking vises secure a workpiece when you pull the lever down. To release the jaw, pull the lever up. Pump - action lever - locking vises allow you to adjust the tension holding the workpiece by pumping the lever. Pull the lever all the way down to lock; pull up to release.

Screw - locking vises engage and adjust the tension with a turn of the screw. Turn in the opposite direction to disengage. They have one smooth jaw and one grooved jaw for clamping flat, round, and uneven workpieces.

Vises with open base allow you to drill through your workpiece without hitting the bottom of the vise. Mount to your vise jaws to create a stop for positioning parts. Turn the spring-loaded screw to adjust and secure on the jaws. A wide opening, large throat depth, and grooved jaws accommodate circuit boards and other flat objects. Clamp and unclamp with one hand by sliding the knurled ring forward to close the collet. Wires and rods can pass through the hollow body.

Contact Us Order. Log in. Create login. Choose a Category. Face Frame. Clamp On. Flooring Clamp. Grip Puller. Heavy Duty. Vacuum Base. Vacuum Base Portable. Product Bench Vise. Woodworkers Vise. Clamping Squares. Bar Clamps. Clamp Rack. Clamp Pads. Mechanics Vise.

Peg Fence. Clamping System Replacement Bars. Dog Peg. Floor Vises. Klamp Table System. Strap Clamp Corners. Bench Dogs. Corner Clamps. Jaw Pads. Parallel Clamps. Pen Press. Replacement Hooks.

Replacement Steel Rods. Steel Rods. Table Clamp. Capacity 12". Jaw Width 4". Material Metal. With a flush-fitting vise, the leg itself serves as a full-length fixed jaw. A leg vise moves via a single screw with a pinned sliding guide rail to maintain parallelism.

The guide-rail pin rests against end-grain hard-maple pads that prevent compressing the softer alder leg of this bench.

However, you can build up some legs to make a leg vise work. These mount to the end of the bench and typically work with bench dogs along the length of the benchtop. If you prefer rectangular dogholes, cut those notches in the boards before gluing them to the benchtop; round holes can be drilled before or after assembly.

A traditional tail vise [ Photos H and I ] consists of a rectangular or L-shape block of wood the jaw fastened to a steel or cast-iron fixture that slides back and forth in a cutaway corner of the bench. A long mortise accepts the screw and threaded fixture, and the upper guide rail fits in the slot. A lower guide rail, not shown, mounts beneath the jaw. The tail vise slides back and forth along the guide rails, held in place by the screw assembly.

Too much clamping force, however, can cause boards to bow up. Typically, you use two rows of bench dogs to hold long or wide stock. The timing chain on a twin-screw end vise syncs the screws. You can adjust either Vise Grip Clamps Woodworking 5g screw should the vise jaws get out of parallel. You can intentionally make the jaws unparallel for clamping irregular-shape workpieces. With an old handscrew clamp and some scraps of hardwood, you can set up your thickness planer to Skip to main content. Bench Vises. Facebook Pinterest Twitter Text.

Iron Branding Logo Java Business Plan Wooden Toys