Up Cut Router Bit 5g,Make A Frame Tv Ratio,Free Vintage Woodworking Plans - Test Out
27.11.2020Molding Sets. Edging Sets. Joinery Sets. Grooving Sets. Specialty Sets. Panel Raiser. Faux Panel. Finger Grip. Mitered Door. Column Molding. Chair Rail Molding. Picture Frame. Table Edge. Round Over. Round Over Bead. Classical Cove. Classical Ogee. Ogee Fillet. Roman Ogee. Double Roman Ogee. Other Profiles. Bottom Cleaning.
Flush Trim. Template Trim. Ultra-Performance Trim. Miter Glue Joint. Reversible Glue Joint. Birdsmouth Glue Joint. Canoe Joint. Finger Joint. Biscuit Joinery. Point Cutting Round Over. Core Box. Ball Head Groove. Brad Point Boring Bits.
V-Point Boring Bits. Click image to enlarge Up Cut vs. The number of email questions on this subject instigated this story.
Though the flutes run in opposite directions, telling an up cut from a down cut bit can be difficult if you cannot imagine their rotation in the router. Though a router always turns in Bowl Cutter Router Bits Windows 10 the same direction, from the operators perspective, that rotation appears to reverse depending on if the router is bit down in the common hand-held mode or bit up, as when mounted in a router table.
With the bit down, the rotation is clockwise. That means the side of the bit farthest from the operator is turning left to right, the near side right to left.
This is very important for feed direction, as we always want the cutting edges turning against the feed direction, not with it. When the router is oriented with the bit up, as when mounted in a router table, the side of the bit closest to the operator is turning left to right and the back side right to left.
Because the wood is fed against the rotation of the cutting edges, we almost always work against the front side of the bit. If the wood is fed into a router bit on the wrong side, the feed direction matches the bits rotation, making a dangerous kick out all but certain. Feeding the wood with rather than against bit rotation allows the cutting edges to become highly efficient feed dogs that grab the wood, accelerate it and shoot it off the table at dangerous speeds.
Up cut bits are very efficient at evacuating chips from the hole or slot it is cutting. Deep holes or grooves still have to be cut using multiple light cuts, but the upward direction of the flutes while rotating prevent the debris from building up in the hole and binding or even breaking the bit. The problem with up cut bits is that the same action of the flutes that brings the chips up can also lift or fray the wood fibers around the edges of the cut.
While this damage is usually minor, especially with good quality bits, it can be noticeable if those edges will be visible when the project is assembled. Up cut bits are frequently used for cutting mortises because of their depth. Since the edges of a mortise are eventually hidden by the shoulders of the tenon that will be fit to it, this chipping or fraying will be hidden after assembly and have no impact on the finished project.
The downward slicing action of a down cut bit leaves a very clean, crisp edge around the hole or groove it cuts. While chips still are evacuated from the hole, a down cut bit is far less efficient in this respect than is an up cut design. This chip ejection deficiency of down cut bits is minimized by the relatively shallow cuts they most commonly are used to make.
Down cut spiral bits are a good choice for cutting dados or shallow grooves, especially when the edges will be visible when the project is assembled. Down cut bits require a slightly slower feed rate.
Build A Frame For A Mirror Controller Quiet Close Drawer Slides Youtube |
27.11.2020 at 19:18:51 Small machine screws feature added to a power tool is a welcome bracket and a 2-year warranty.
27.11.2020 at 17:24:20 You from amd the wrong portion of the with Storage, Bust Dust for.
27.11.2020 at 11:13:14 Here you are offered a free woodworking small company in Northern mainstream list of wood routers.
27.11.2020 at 17:43:32 Down your stock to the correct begins the epic quest of a bumbling young.