Head off scratches with a light polish. The port will be where your steam supply is delivered. The idea is to suspend it in the air to allow the steam to flow around the wood in the bag as much as possible. Press the wood firmly against it, using C-clamps and guides along the way. This means that you steamer for bending wood tree a ton of insulation. Steam blanks for one hour per inch of thickness regardless of steamer for bending wood tree width. You then compress the wood, and the notches act like reliefs and create a weak point in the wood that you can bend at.

Cut plywood to create forms to shape the wood you want to bend. Attach several small curved pieces of plywood to a board to create a bending board, or cut large forms that you can clamp the steamed wood to. You will attach the steamed wood to this form with clamps. Alternatively, cut up several smaller curved pieces from plywood or MDF, then screw or nail them to a backboard to create a mold for your steamed wood.

You will need to make pieces for the inside and outside of the curves so that the steamed wood is held in place between them. Clamp the steamed wood to the forms if you cut large plywood forms. Place the wood you are bending against the form, then clamp it to the form.

Start with the flattest area, secure it in place, then carefully bend the wood around the form. Try to work as quickly as possible. The longer you take, the harder the wood will be to bend. Place the steamed wood in the mold if you made a bending board.

Carefully bend the wood in between then curved pieces of plywood or MDF Making A Steamer For Bending Wood that you used to make a mold. Start at one end and work your way to the other. Let the wood sit against the form or in the mold for 24 hours.

Leave the wood to cool, dry, and set for at least a full day. Unclamp the wood from the form or remove it from the bending board mold after a day has passed. Include your email address to get a message when this question is answered.

Submit a Tip All tip submissions are carefully reviewed before being published. Always wear heat-resistant gloves and safety goggles when steam bending wood. Helpful 0 Not Helpful 0. Related wikiHows How to. How to. More References 6. About This Article. Co-authored by:. Co-authors: 2. Updated: April 8, Categories: Woodworking. Thanks to all authors for creating a page that has been read 30, times. Did this article help you?

Yes No. Cookies make wikiHow better. By continuing to use our site, you agree to our cookie policy. Related Articles How to. Categories Hobbies and Crafts Woodworking. By signing up you are agreeing to receive emails according to our privacy policy. Follow Us. X Help us do more We've been helping billions of people around the world continue to learn, adapt, grow, and thrive for over a decade. Legend has it that Pan changed her into a reed because she rejected his romantic advances.

He did give her a song that you are supposed to be able to hear when the wind blows through the reeds. Cool huh? Another example is this piece. It was made for an aromatherapy candle shop. Imagine the two upright spires are the flame, the curved piece is the aroma of the scented candle rising in the heat, and the partial circle is the glow of the candle.

Click here to cancel reply. Remember me. Lost your password? Privacy Policy. LOG IN. Search for:. Become A Member. Facebook Instagram Pinterest Youtube Twitter. Cut stock for parts requiring tight bends so the annual rings lay flatwise against the surface of the bending form [ Drawing delow ].

For mild bends, grain orientation Plum Tree Wood For Turning Edge is less important. Steaming takes about one hour per inch of workpiece thickness and parts must stay on the bending form for one hour, so unless you make more than one form, the steam box only has to accommodate one part at a time.

For efficient use of the steam boiler [ Sources ], a steam box should be only large enough to hold the part blanks with room all around for good circulation.

For tight bends on thick parts, increase box size to accommodate resteaming a partially bent piece. The steam box shown in [ Drawing below ] holds two leg blanks for the desk shown above and accommodates resteaming of a partially bent leg. Make bending forms from particleboard or plywood laminated to a thickness equal to the width of the bending blank.

Bending a workpiece puts considerable stress on the form, so when in doubt, more form width beats less every time. Bent parts retain most of their shape after cooling but to minimize springback, must be held to a form until completely dry. The forms shown [ Drawing below ] are for the desk, shown in photo above.

We made six drying forms to accommodate four leg blanks plus two extras. Securely clamp the bending form to a sturdy workbench. Have all clamps handy. Bending should be accomplished within five minutes after removing the blank from the steam box so you may want to rehearse your procedure. Fire up the boiler. When steam steadily flows out of the drain hole, slide your blank into the steam box. Steam blanks for one hour per inch of thickness regardless of the width.

Remove the part from the steam box and bend it [ Photos below ]. Working quickly, position the steamed blank between the anchor block and the end block on the tension strap assembly. Clamp the blank to the bending form and bending arm, applying clamps both vertically and horizontally. Begin to bend the blank around the form. Thick parts, such as the legs on the desk, require significant force so put your body into the bend or enlist a helper. Thick parts, such as the legs on the desk, require significant forcea so put your body into the bend or enlist a helper.

Thick parts may not bend in one operation. When you feel too much resistance, remove the part from the form and re-steam it for 15 minutes. As the bend nears completion, remove the bending arm clamps interfering with the bend. Then draw the free end against the form with a one-handed bar clamp. Clamp the straight portion of the leg to the form and then add clamps along the curved section. Allow the part to cool for one hour and then quickly transfer it to a drying form.

Kreg Jig 5 Home Depot Manual Hardest Wood For Turning Questions Marking Knife Ebay Coupon