Лампы и светильники. Абажуры и основания для ламп. Основания и провода. SKAFTET СКАФТЕТ Основание настольной лампы. Стильный современный дизайн, который вы можете дополнить абажуром или Skill Saw And Table Lamp декоративной лампочкой на свой вкус. Для создания выразительного интерьерного освещения используйте и другие светильники серии СКАФТЕТ.  SKAFTET СКАФТЕТ. Основание настольной лампы, черный30 см. ₽. Лампочка продается отдельно. -1 Lamp Stem I used PIST08 from Grand Brass they have a variety of finishes and lengths available make sure to go with the long thread to have enough thread to bolt to the saw. -3 nuts for stem NU from Grand Brass. - 1 saw blade I used a junk one some saws may have the blade in them.  While most lamps do not have a ground it does add a level of safety and since I used the 3 wire cord to retain the look of the saw I was able to ground the lamp. -Remove the base from the lamp fixture, in most cases this will just clip on but some fixtures may use screws. Route the wires through the fixture base and thread the base to the stem. The best bedside table lamps are ones that makes you smile when you see them. Your bedside lamp is the very last thing you touch before bed, and its light is the last impression you get before you fall asleep. This means that, although it may be a small thing, your lamp is actually an important part of your personality. 25 Elegant Bedside Table Lamps for Your Bedroom. With that in mind, what kind of lamp do you click off every night? Do you pull the cord on a vintage lamp with a flaxen shade? Do you touch the base of a modern lamp and cycle through a few brightness settings? Or do you flip th. Route the wires through the fixture base and thread the base to the stem. Get Connected. Measure the length of the lamp stem and add about 2 inches to that for wiring the lamp fixture. A tubing bender is ideal however if saw and table lamp is not available you can clamp in a saw and table lamp and slide a larger piece of talbe over the stem to bend it, be careful not to kink the stem when bending with this saw and table lamp. Your request znd not have been tzble sent. My granddad was always building lamps out of unique items I have a set he made out of old brass machine oilers and one made out of the steam whistle off his old sawmill. If the cord on your saw is in good condition you may be able to reuse it for your lamp however in most cases with a saw of this age the cord will have cracks and cuts and need to be replaced.

The tools I used are. The first step of this project was to remove the old cord and switch or any other parts that may interfere with the mounting of the lamp stem and new wire routing. If the cord on your saw is in good condition you may be able to reuse it for your lamp however in most cases with a saw of this age the cord will have cracks and cuts and need to be replaced.

A dremel or grinder with cutoff wheel would also work for cutting the trigger off. I had decided that I wanted to mount the stem for the lamp off the handle, this allowed me to position the lamp close to center of the saw and to route the cord for the lamp in the same way that the original cord for the saw was routed.

Depending on the model of your saw you may chose to mount the stem in a different location. A tubing bender is ideal however if one is not available you can clamp in a vise and slide a larger piece of pipe over the stem to bend it, be careful not to kink the stem when bending with this method.

I clamped the stem 3 times in different spots and did 3 small bends for a smooth sweep. Tighten nuts using a suitable wrench. Wiring the lamp may differ slightly from the pictures depending on the components you purchase or Saw And Table Valve scavenge for your lamp. The cord I used was scavenged from a old stereo amp and the colors differ from a typical cord which would have a white neutral and a black hot wire. You will need to strip enough insulation from the cord to feed the neutral and hot wire up the lamp stem.

Measure the length of the lamp stem and add about 2 inches to that for wiring the lamp fixture. I have found the best way to cut the insulation is to bend the cord in a loop and lightly cut the outer edge of the loop. Be careful not to cut into the wires. I used the original strain relief and wire clamp to clamp the wires. I also attached the ground to the original ground location. While most lamps do not have a ground it does add a level of safety and since I used the 3 wire cord to retain the look of the saw I was able to ground the lamp.

Route the wires through the fixture base and thread the base to the stem. I used a nut to jam nut the base so it would not turn.

The socket will typically slide out of the outer tube allowing access to the terminals. You will notice that one terminal has a lighter color than the other this indicates it is the neutral terminal and should be attached to the white wire on a typical cord. I added pictures showing another socket and a cord with white and black wires.

Test the wiring. If the lamp is not wired properly it will still work however the neutral wire will be switched instead of the hot wire, this leaves the outer portion of the socket energized at all times which is dangerous. I did a quick continuity check with a multi meter to ensure it was properly wired.

See attached photo for further instructions on this test. I wanted to have a blade in my saw and make it look like it is cutting a piece of wood to do this I wanted the blade to sit in a notch in the wood base but didn't want the notch to cut all the way through my board. I cut the bottom of the blade off where it sits in the notch.

In the pictures I am using a plasma cutter to do this but if you don't have a plasma cutter a cutoff wheel in a angle grinder will work. The base can be any board of your choosing, I had a piece of Osage Orange laying in my shop and used it.

Yellow pine dimensional lumber from your local hardware store would work as well and you can finish it with stain or clear coat to your liking. Place a mark at the front of the blade indicating where the notch should stop. I left the remainder of the line I marked on the top so that the saw looks like it is cutting the board.

Showing Products: 1 - 5 Of 5. Showing Products: 1 - 3 Of 3. What Our Fans Are Saying. Clear All Filters. Loading Results. You Might Also Like. Get Connected. Email Address Field 'Email Address' is required. Trade Field 'Trade' is required. Country Field 'Country' is required. You have successfully signed up to receive an email about special offers, new products, and events! We experienced a technical difficulty while processing your request.

Your request may not have been correctly sent. By signing up, you agree to receive emails from Milwaukee with news and other information.

Olive Wood For Turning Point Router Guides Templates Not Found Sign On Router Red Talk