Looking to make your own DIY cabinet doors? It also contains affiliate links. See policies. Thank you, Captain Obvious…. But, seriously. All cabinets router bits to make cabinet doors on basically the same thing…just a simple box. Those are the stars of the show.

So when my very traditional sister asked me to build her new cabinets, of router bits to make cabinet doors on, the doors were a major concern. No, she wanted a decorative edge along the inside of the door frame. For this situation, I was building my sister brand new cabinets. And she wanted them painted white. I chose these options because they are easy to router bits to make cabinet doors on with and paint really well.

There are a million ways to make a door, but this method is fairly simple and worked with the tools I already had. Because my sister likes to make things difficult love you, Sissy! So I used my trim router and a round over bit to cut a nice round over edge on the same side of the board as the dado.

Side note: I will admit, this really did make these doors look nicer than a standard, plain square edge…BUT it added quite a bit of work. See step 5…. I know you will ask router bits to make cabinet doors on to determine the size your door needs to be.

I prefer frameless, but most people have face frames. For cabinets with face frames, if doing partial overlay, add 2 times whatever you want your overlay to be to the height and width of your inside opening and be sure get hinges to match your overlay.

This is the style I went with. Check out my post here about to build frameless cabinets. So they had to be mitered. So I measured the sizes I needed my doors to be see step 4 and began cutting my pieces with 45 degree miters on each end. I measured and cut based on the long sides and made sure the short sides had the dadoes and the round over edge. Basically, I cut the pieces to the size my door needed to be.

Make sense? Now for the fun part. I laid my frame out on my workbench and used a square to mark lines along the diagonals in the corners. This is just to line up my dowel jig. Then, I centered the center line on my dowel jig with these lines, clamped it, and drilled two dowel holes in each board end. Once the holes were drilled, I used wood glue and dowels to join all the corners. I found it easiest to put three pieces together one short and two longthen slide the panel in place, then add the last piece of the frame.

Once everything was together, I used some pipe clamps to clamp it in place and make sure it was nice and square and my corners lined up well. I wiped any excess glue away so it will be easier to sand later. Once the glue was dry, I gave the corners a good sanding to get everything nice and smooth and sand out any unevenness at the joint. And to remove any glue squeeze out. Then, I puttied the corners as needed if there were any small gaps or dentssanded again, and caulked along where the panel meets the frame for a cleaner paint job later.

I like to hang my cabinet doors using concealed hinges because they offer three different adjustments to get your door to router bits to make cabinet doors on just right. I have a post here all about concealed hinges and how to install them. In that order. To finish the cabinets doors, I simply applied a coat of general latex primer, then lightly sanded with grit sandpaper once it was dry.

I used three coats of paint to get good coverage and sanded between each coat. A huge help during the cabinet door installation was this Werner 10 ft Podium Ladder.

It was the perfect height to be able to stand securely to install the doors and the cabinet pulls, but the podium also provided a great place to place my tools, drill bits, screws, etc. And once the hardware was in place and the doors were hung…well, there was still a lot of work to do with trim and caulk and shelves and such.

But at least the doors were done haha. The extra decorative edge along the middle really makes them look professional. So, if you are looking to build your own DIY cabinet doors, I hope this router bits to make cabinet doors on has been helpful and inspiring.

Be sure to check out the video tutorial as well and stay tuned for more info on how I designed and built these cabinets coming soon.

Facebook Instagram Pinterest YouTube. Next Post: How to Tile a Backsplash ».