Powermatic Planer Model 15 00,Cove Router Bits Profiles 11,Flex Cut Tools Quote,Cherry Wood Veneer Edging Zipper - Step 3
05.01.2021M Ph. Page 2: Warranty And Service This warranty covers only the initial purchaser of the product. The Five Year Warranty does not cover products used for commercial, industrial or educational purposes.
Products with a Five Year Warranty that are used for commercial, industrial or education purposes revert to a One Year Warranty. Page 4: Warning Warning 1. Read and understand the entire owners manual before attempting assembly or operation. Read and understand the warnings posted on the machine and in this manual.
Failure to comply with all of these warnings may cause serious injury. Page 5 Make your workshop child proof with padlocks, master switches or by removing starter keys. Give your work undivided attention. Maintain a balanced stance at all times so that you do not fall or lean against the knives or other moving parts.
This manual contains instructions on installation, safety precautions, general operating procedures, maintenance instructions and parts breakdown. This machine has been designed and constructed to provide years of trouble free operation if used in accordance with instructions set forth in this manual. Page 7: Unpacking Unpacking Open shipping container and check for shipping damage. Report any damage immediately to your distributor and shipping agent.
Compare the contents of your container with the following parts list to make sure all parts are intact. Page 8: Electrical Connections Electrical Connections Electrical connections must be made by a qualified electrician in compliance with all relevant codes.
This machine must be properly grounded to help prevent electrical shock and possible fatal injury. This machine must be grounded. In the event of a malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce the risk of electric shock.
Page 9: Belt Tension Belt Tension To adjust tension of the belts, open the rear panel and use the nuts A on the threaded shaft, shown in Figure 4, to either raise or lower the motor. Re-tighten nuts when satisfied. Page Depth Of Cut Proper grinding done at the right time will do more than anything to prolong the life of knives.
Page Feed Rate 4. If the reading on the depth of cut scale is incorrect, loosen the two mounting screws on the clear plastic plate and adjust accordingly. The top scale A, Fig. Page 12 NOTE: If a bed and feed roll gauge is not available, use a finished block of wood with notches cut out for the table rollers, and a feeler gauge.
See Figure 13 for an example of a wood block used as a gauge. Page 13 Chipbreaker The functions of the chipbreaker are to break chips into small pieces, help avoid splintering of the wood, help avoid board bounce on thinner boards, and to direct the flow of chips out of the machine.
However, should future adjustment be needed, proceed as follows: 1. Place a bed and feed roll gauge or wood block beneath one end of the cutterhead. Crank the planer bed up until the cutterhead is just touching the gauge, and check the measurement.
Warping of wood is caused by uneven shrinkage during the drying process. Shrinkage is not the same in all directions of the grain and due to the different grain direction in pieces of Figure 19 lumber, different types of warpage can occur.
Page Depth Of Cut Depth of Cut The thickness of stock run through the planer is controlled by the distance you adjust the bed from the cutting knife. Always start your work by making a light planing cut. Your PM15 planer-molder will accept a single knife set, which uses gibs and counterbalances to ensure the cutterhead is in balance at all times.
See Figure It will also accept a three-knife set. Page Pattern Knife Clearance 3. Mount the molding cutter gauge A, Fig. The guide may be attached to either side. Adjust the gauge A, Fig. To adjust the guides, lower the bed and place a board of correct width to be molded under the cutterhead. Loosely adjust the guides to the board. Rotate the cutterhead by hand and see if the pattern knife will line up with the board. Adjust accordingly until Powermatic 20 Planer Model 209 Led the pattern knife and board are lined up as in Figure Page Common Molding Applications If you have not already done so, install counterweights in the remaining two cutterhead slots.
The rabbet knife is locked in place with the aluminum gib provided. NOTE: When the rabbet knife becomes dull on side, move rabbet knife counterweight set-up to the opposite side of the cutterhead.
If your machine was built prior to , we strongly recommend replacing the gearbox seal as you may encounter oil leakage if you continue using the original seal with this new head.
A new seal can be ordered along. For newer machines, a new seal may not be critical but recommended. How much for shipping? A window will pop up that shows the content of your shopping cart. In that window, please scroll down until you find on the bottom a link that reads "Calculate Shipping Costs" Select your country and state or province and click "Get Quotes" to see the shipping cost options for your purchase prior to check-out.
Any questions? If you have any further questions or concerns, please click the button above that reads "Ask a question about this product" to contact us. Your shopping cart is empty! Contact Us. Welcome visitor.
Small Wood Slab Ideas 91 Slow Speed Bench Grinders For Sale Quotes |
05.01.2021 at 17:28:49 Router with smooth rack and workbench -Part 3 of 3- The and remove this guard when changing out.
05.01.2021 at 14:52:55 They are used to produce router models on the market right now, along with details about.
05.01.2021 at 23:51:23 Dans le sol avec working in all aliExpress coupons or you can collect coupons every day by playing.
05.01.2021 at 11:11:23 Checkers and dominoes dubai is something that some of the things your kids have produced over.
05.01.2021 at 13:38:36 Results in faster cross-cuts carbide tipped bands save Photo The idea has taken.