LibreRouter is an Open-Source Hardware Router for Community Networks

A few open hardware router name ago we asked a simple question - what do you use for your router, and what would you look for in a router review. Picking that hardware is often a function of what software can be tossed on top, open hardware router name having a consistent and familiar set of configuration pages makes setup and maintenance much less of a nightmare than dealing with the third party alternatives. There are so many arguments for using some open source package instead of the first party software which is usually derived from the board software package the SoC vendor hands out.

In the responses to that article, a few major things open hardware router name out for me: what is the current landscape as far as hardware goes, and what performance impact if any is there that arises from running a third party software package on a router.

I've split the follow up into two sections as a result. The first focuses on the current hardware landscape, and the second is a performance investigation of the third party software packages. Ganesh and myself are currently sitting on open hardware router name This is by no means a be-all or end-all review, but hopefully gives a bit of perspective for users setting up a connection for the first time and looking for a router, or wondering about the differences between a few different popular platforms.

The motivations for installing third party firmware on a router are often pretty simple: for adding features, increasing stability, or the desire for a better designed UI. Some of the original desire open hardware router name move to third party firmware in years past was born out of necessity - a limited number of NAT connection states made use of P2P across some routers impossible without third party software.

Other features that drive people to open source distributions include better QoS Quality of Service traffic shaping and management, static DHCP functionality, the ability to mount and serve attached storage or printers, compatibility with a wide variety of VPN services, ability to change WiFi Tx power, client status reporting, and even overclocking.

Open hardware router name the purposes of this piece, I chose two hardware platforms that have seen widespread adoption and have great support among the most popular open source third party router firmwares.

In the next article I'll also toss in my venerable WRT54G-TM into the fray, just to illustrate how that platform performs in comparison with much more modern hardware. It seems like just about every third party platform I can find supports open hardware router name RT-N16, and the device even has a small but growing lineup of accessories, including external open hardware router name for overclockers really.

The features that make it desirable are actually pretty straightforward. First, it has three easily removable antennas which are just screw-on SMA connectors. This makes it easy to upgrade or replace the stock 2 dBi antennas with just about anything. SMA antennas are very easy to find these days, I literally have a drawer full of antennas with SMA connectors, from highly directional yagis or a cantenna, to directional patch antennas, or very flat profile 9 dBi omnidirectional ones as shown below.

I opened up the RT-N16 and all of this is visible immediately. The BCM SoC is under a small heatsink at center which is held open hardware router name with some double sided tape and easy to upgrade if you want to push it all the way to MHz.

This third antenna is used in a switched diversity mode to increase signal to noise ratio at the receiver. Next, the RT-N16 includes gigabit ports all around, and a four port switch open hardware router name supports jumbo frames. The power supply is an external wall unit which is pretty standard, which supplies 5V at 1. Having MHz of x86 makes the platform very well suited to doing Open Hardware Car Name much more than a cheaper off the shelf router platform.

PC Engines makes the board, and you can either assemble the mainboard and chassis yourself by ordering from them, or go to an assembler and get the whole combo including power supply in a nice wrapped up package. It truly is some of the most robust hardware out there, usually with insane uptime in the months or years.

In part 2 we'll focus on on some of the third party software packages and how they perform on these platforms. Stay tuned! Open Source Router Spotlight Open hardware router name few months ago we asked a simple question - what do you use for your router, and what would you look for in a router review.

Hardware For the purposes of this piece, I chose two hardware platforms that have seen widespread adoption and have great support among the most popular open source third party router firmwares. Post Your Comment Please log in or sign up to comment. I live in a condo with a lot of noise so I had to get 5Ghz routers eventually settled on the Linksys E's, which are not as nice, but work better for my purpose. Will the switch to ARM be a good or bad thing for third party software?

Privacy Open Hardware In Quezon City Name Policy. Contact Us. Terms of Use. Show Full Site. All rights reserved. Log in Don't have an account? Sign up now Username Password Remember Me. Lost your password?

Jun 24,  · Launch a web browser from a device that is connected to your router's network. Enter www.- or http:// in the address bar. The router login window displays. Enter the router admin user name and password. 26 rows · Name Status Type Architecture Min hardware requirements License Cost Description . Dec 02,  · The router, at least the common home network device that is usually called a router, is the piece of network hardware that allows communication between your local home network—like your personal computers and Open Source Hardware Group Name other connected devices—and the internet.

Pocket Hole Jig In Spanish 30 Plywood Furniture Plans Free Movie Pocket Hole Jig On Mdf Ltd