Plunge the router down until the router hits your workpiece. Buyer Protection How you're covered. The first thing to do is work on the platform by cutting all the pieces to rough length. Similar Items. Any delays in delivery will be communicated to you.

Just a note, the final version of this was created by Mike Taylor from TayTools. While he did not sponsor this project, you can help support what he does by purchasing some of the hardware for the jig using the links above. The first thing to do is work on the platform by cutting all the pieces to rough length.

Cut them oversize for now, they will be trimmed to final length after glue-up. You should have 2 pieces at rough length and width for the platform.

The next piece on the other hand needs to be very precise…. This is the spacer that will determine the opening in the jig. This piece needs to be the exact width of the guide bushing you plan on using so there is no slop in the jig. To get this piece to be the exact width of the guide bushing you are using, use some calipers!

Then bring that measurement over to the table saw and set your fence. Easy enough! Before cutting the actual piece, do some test cuts on scrap wood to dial in the perfect thickness. Once you have that dialed in, you can rip the actual piece and then cut it in half to create two spacer pieces. Temporarily clamp all the pieces together and test fit the guide bushing one last time to make sure there is a tight fit before glueing anything together.

Another thing to do before glue up is to score a center line in one inside edge. This is just easier to do now before it is all glued together. Use a marking knife, then fill it in with pencil or pen so you can see it very clearly.

This center line will be useful when actually using the jig. You can also mark a center line on that scrap spacer and line it up with the center line you scribed on the inside edge of the platform piece to make sure everything is glued up where it should be.

While the glue is drying on the top platform you can start to work on the fence piece. Trim it to rough length and width at this point in anticipation of tear out from the router bits. All the clamps and fixtures are going to attach to the jig using special hardware that has a dovetail shape on them.

To avoid tear out though, there is an optimal order of operations. This is the best way to avoid tear out in the middle of your board. Now that the slots are routed, you can cut it to final length and width by taking off the same amount of material from either side.

The platform gets those same dovetail slots, one on each end of the board. There will be tear-out on those cuts! So use some calipers to make sure all the edges are parallel.

Add a center line along the bottom of the platform using the center line you already scribed on the inside edge before glue up as a reference. Fill in the scribe line with some pencil so you can see it more easily.

A center line also needs to be scribed along the length of the bottom of the platform. This can be done with a wheel marking gauge, and you know it will be perfectly centered if you reference both edges. Drill and countersink holes on both edges of the platform for the screws that will hold the width stoppers. Use the actual dovetail slots you routed under the platform as a guide for where to drill though holes on the edge of the fence. These holes need to line up with those slots since that is how you will be mounting the fence to the platform.

Drill out the through hole from both edges so that they meet in the middle. And repeat, you should have two of these to attach the fence to the platform. Orders within other provinces will be delivered to your nearest Paxi or Pargo point for collection. This time frame is only an estimate based on the majority of orders. Most orders will arrive sooner. Certain types of products can not be sent via International Courier Delivery, please inquire if you need more information.

Should you order a product that has restrictions on shipping then we will contact you and offer a resolution, other options or a full refund. In the event that your order does not arrive within 60 business days due to customs delays or any other uncontrollable reasons then we will then resend the order free of charge or refund the order in full.

Any delays in delivery will be communicated to you. Customs Duties and Clearance: No customs duties to be paid. All costs are inclusive in the product price. Faulty or Damaged Items: Faulty or damaged items must be reported within 7 business days to qualify for a refund or exchange.

Certain products may require a lead time of 5 - 10 business days to process and therefore tracking details may be delayed. Payment More info. Item information. Similar Items. Local pickups and combined shipping options are not provided at this time. You can return a product for up to 30 days from the date you purchased it. Any product you return must be in the same condition you received it and in the original packaging. Please keep the receipt. Please visit our eBay store to check out other items for sale!

Woodworking Plans Room Divider Design Professional Woodworkers Supplies Jobs Sash Window Router Bit Set 80