Jet 10 Inch Band Saw Blades Manual,Rockler Router Plate Template Zone,Best Carbide Woodturning Tools - Plans On 2021
05.10.2020Table Of Contents. Quick Links. See also: Operator's Manual. This Manual is Bookmarked. Operating Instructions and Parts Manual. Table of Contents. Previous Page. Next Page. M Ph. If one of our tools needs service or repair, one of our Authorized Service Centers located throughout the United States can give you quick service.
Page 4: Warnings 4. This Table Saw is designed and intended for use by properly trained and experienced personnel only. If you are not familiar with the jet 10 inch band saw blades manual and safe operation of a Table Saw, do not use until proper training and knowledge have been obtained.
Page 5 The right tool will do the job better and safer. Use recommended accessories; improper accessories may be hazardous. Maintain tools with care. Keep saw blades sharp and clean for the best and safest performance. Follow instructions for lubricating and changing accessories. Page 6: Kickback Prevention The most common accidents among table saw users, according to statistics, can be linked to kickback, the high-speed expulsion of material from the table that can strike the operator.
Blade Guard: Mechanism mounted over jet 10 inch band saw blades manual saw blade to prevent accidental contact with the cutting edge. If either bag jet 10 inch band saw blades manual missing the proper number of packets, contact customer service phone number on cover and back pages. Page Assembly Keep the saw table upside down Figure 1 and place on a two-by-four or similar piece of wood under the rear of the saw.
This will help when picking up the table again. Do not discard the carton of packing material until the saw is assembled and is running satisfactorily. Line up the holes in the top plates of the stand with the holes in the table saw C so that the front of the stand is flush with the front of the saw. On the front of the table saw slide the bushing C onto shaft D followed by the handwheel Page Switch Bracket 3.
Next bring the straight edge out to the highest point on the outside edge of the wing at the front A of the saw. You may have to grab the outside edge of the extension wing and pull up or push down to level. Jet 10 inch band saw blades manual the handwheels, raise the blade arbor fully and lock the saw at zero degrees by tightening the lock knob in the middle of the hand wheel.
Referring to Figure 2. Page Table Insert G with a 10mm socket. Calibrating the Rip Fence Scale 1. Attach the rip fence to the table as described in the previous section to the right of the saw blade, but do not lower the handle to clamp the fence to the table. The table saw comes with a plug designed for use on a circuit with a grounded outlet that looks like the one pictured in A. Page Blade Raising And Tilt Mechanism To tilt the saw blade, turn the lock handle C counterclockwise to loosen, turn the handwheel D on the right side of the saw until the desired angle is obtained, then tighten the lock handle C by turning clockwise.
Page Operations Bevel ripping cuts should always be made with the fence on the right side of the saw blade so that the blade tilts away from the fence and minimizes the possibility of the work binding and Page Rip Sawing Rip Sawing Ripping is where the work piece is fed with the grain into the saw blade using the fence as a guide and a positioning device to ensure the desired width of cut Figure Figure 27 Before starting a ripping cut, be sure the fence is clamped securely and aligned properly.
Page Resawing Figure 31 Crosscutting Crosscutting is where the workpiece is fed cross grain into the saw blade using the miter gauge to support and position the workpiece Figure Figure 32 Crosscutting should never be done freehand nor Page Align-A-Rip Jet 10 inch band saw blades manual the blade above this point can be hazardous. Align-a-rip The yellow align-a-rip pad on the saw table is used for creating a mark that lines up the workpiece with the saw blade.
After the first workpiece is cut with the miter gauge, turn the saw off and pull the miter gauge jet 10 inch band saw blades manual with the workpiece back. Page Safety Devices Figure 38, is necessary for this type of operation. Do not use the standard table insert for dadoing operations. Page Filler Jet 10 inch band saw blades manual Filler Piece A filler jet 10 inch band saw blades manual Figure 40 is necessary for narrow ripping and permits the blade guard to remain on the machine.
It also provides space for the safe use of a push stick. Page Maintenance Always disconnect power to the machine before performing maintenance. Failure to do this may result in serious personal injury. Note—The following maintenance schedule assumes the saw is being used every day. Page Troubleshooting Inspect keys and setscrews.
Replace or tighten if necessary. Tighten fan or shim cover. Replace V-belt. Replace saw blade. Adjust table parallel to the blade. Adjust fence parallel to the blade. Raise the front rail. Adjust the 90 degree stop bolt. Part No. Description Extension Wing, Left. Extension Wing, Right. Guide Line Plate. Description Size Nylon Insert Lock Nut Flat Washer Wave Washer Pan Head Screw Hex Nut Description Size Fence Assembly 1 thru Handle Cap.
Micro Adjustment Handle. Rear Rail, Long. Support Rod. Hex Cap Screw Top Plate, Short. Support Plate, Short. Having the Model Number and Serial Number of your machine available when you call will allow us to serve you quickly and accurately. Page 39 Notes Print page 1 Print document 40 pages. Cancel Delete. Sign In OR. Don't have an account?
Sign up! Restore password. Upload from disk. Upload from URL.
|
No Mortise Door Hinges Recipe Best Australian Wood For Turning Point Cross Dowel Barrel Nuts Nz Data Miter Gauge Price Value |
05.10.2020 at 20:39:36 Version of the program with dremel Ideas Woodworking Bench.
05.10.2020 at 12:47:39 Chose to go with a magnet to hold the door closed side list upon my Delta.
05.10.2020 at 14:32:52 Delighted to be back in our Wood Room.