What do you think of this sled? Is anyone using this sled for complex work? Any links so I can learn how to amp up the performance? Reply.  I have Incra gauges but, I believe the sled uses a different slot adjustment method. The miter gauges have Incra 5000 Table Saw Sled Qt discs that you expand by tightening the screw. Does the sled use the adjustable wedges? If so, you tighten the wedges to the point that the sled slides easily but, is snug in the slot. It is a balancing act between too tight and too loose. If you cannot get a setting that is reliable through the full length of the slot, your slot is irregular and a spring-loaded ball type glide (although I do not find then satisfactory) may be the answer. The Miter blends the incremental angle control features of the Miter SE with a special 3-panel Sled for exceptional accuracy, capacity, and control. 20”” panel cutting capacity on most saws plus T-tracks and a heavy duty hold down clamp for controlling small parts. Miter gauges don’t offer control or accuracy when pulled beyond the front of the saw, while the can crosscut 23" x 34" plywood cabinet sides with ease on most full size 10" table saws. The 36" to 64" telescoping IncraLOCK Fence and Flip Shop Stop have plenty of range for long boards.  - Fence lock down clamp for rock solid support. - Miter Slider included for static sled panel positioning. INCRA Miter SLED CompatibilitY: Miter slot size. So I went to do a little project last night and discovered that my Wood Whisperer crosscut sled is all out of square. The front rail is no longer perpendicular to the base and its also not square to the blade. I made the thing out of 2x4's and particle board which I know wasn't smart but its what I had at the time. It was very square and worked great until a few hot/cold temperature cycles in my shop which is not heated or cooled. Now its all wonky and basically ready for the scrap pile.  Am I giving the Incra too much credit by assuming it could be my workhorse for crosscutting? Would it be okay in the cold/hot shop or would I have to bring it and put it to bed every night? Is there something else that does the same thing for less money?. I find that I get cranky and incra sled 5000 error "I'm sacrificing too much" if I don't purchase a frivolous item every now and again. Reset My Password. Display as a link instead. Tilt the head of your miter gauge errof use its auto stops as you normally would to make an angled cut. Where do the two parts separate?

Home Incra Miter Incra Miter This product has an estimated ship date November 10, Skip to the end of the images gallery. Skip to the beginning of the images gallery. The new MITER incorporates patented innovations like an adjustable steel miter bar with ten, low friction nylon expansion points.

Additional Information. Ahh ok. You have just the gauge not the additional sled, gotchya. Just curious. I have the se but wanted to upgrade to the I've been watching Marc with the 5k and I'll be honest, I just don't think it would work well with my flow. I'm sure it's a great tool, Incra doesn't usually make junk.

I'm changing what I'm doing on my TS too often to want an off cut support on my table all the time. You can post now and register later. If you have an account, sign in now to post with your account. Paste as plain text instead. Only 75 emoji are allowed. Display as a link instead. Display all pictures.

Achieve gap-free glue joints on mitered corners of any multi-sided object without trial-and error setups! Cancel or. This product is not sold individually.

You must select at least 1 quantity for this product. Availability date:. Just slip the bar of your Mark 7 or Mark V miter gauge or any miter gauge into the piggyback T-slot in the top of the miter sled and twist the three small cam locks that hold it in position there. Once you're docked and locked - you're ready to go to work.

Your miter sled will now give you a stable, generous-sized platform to carry your stock safely and precisely through the cut.

Wolf Circular Saw Blades 2020 Router Bits On Sale Edition