Local Pickup. Decide how you want to shape the hand plane, or follow my basic shape in the illustration. This is what your wood should look like when you get it all set in the vise and appliance. I dunno — three to four minutes. Now Dennis spends hand plane jointer jig journal time on fine woodworking projects and tool comparisons. No screaming motor.

I just prefer the wooden soled plane because I think it slides more nicely on the wooden edge. From there, I get out my trusty Veritas bevel-up jointer plane.

Yes, I bought a newly Hand Plane Jointer Jig Repair minted plane instead of finding a quality used one. Since my shop is relatively crowded, and the plane was less expensive than a powered jointer, I figured I would spend the money I was saving for a powered model on this beautiful tool.

I also bought the 90 degree fence for the plane. True, if I was edge jointing two boards for a glue up, I could plane them both side by side in the vise, with any variations in angles canceling each other out.

But, I have found that true, crisp 90 degree angles glue together more nicely. The technique is very simple. When you start planing, push down hard on the front knob while you push the plane along. Once the plane is completely on the board, push down evenly as the plane glides along. When you get to the end, relax your pushing down on the front knob and bear down on the tote the back handle.

Think about scooping up a bucket of water. Practice, practice, practice and it will come easily. As you can see, the are the nice, board-length curls you come to expect from a hand plane. The real test comes when you run a square along the edge to confirm you have planed at 90 degrees, and you remove the board from the vise and appliance and lay it down on the bench top. You should not be able to see any light passing under the board.

Total time to edge a board? I dunno — three to four minutes. No snipe. No screaming motor. No chance of losing fingers or the board exploding if a jointer knife snags a knot. Thanks for the tutorial. Looking forward to practicing! Attach the stop to a substantial keel and note that the longer the keel the wider the stop will be, and the wider the stop the less it will deflect under pressure.

Although the stop is cross-grain to the keel, the thinness of the stop makes it unimportant to worry about any difference in seasonal wood movement. A small crack or two will hardly affect the utility of the fixture.

Should your bench top not be perfectly flat, or if the board being planed is slightly bowed, when you attempt to plane the high side the pressure of the plane may cause the end of the workpiece held against the bench stop to rise — and no longer be held in place.

The solution is to use a specially prepared, perfectly flat board, at least as big as the workpiece to be planed, which can be more easily held against the stop. A couple of flathead woodscrews which may be raised or lowered according to the thickness of the workpiece will act as stops.

If you have any concern about the screws damaging the end of the workpiece, attach a small stop strip to the board as well. As a further precaution against the workpiece lifting clear of the Hand Plane Jointer Jig Youtube stop or of the screws when you apply pressure to its center, place a shaving or two under the high spot. Construction — The planing board is one example where medium density fiberboard MDF is perhaps the best material since it is not likely to warp.

However, the use of a thin stop strip rather than screws is a better idea with MDF since constant adjustment of the screws will eventually cause them to fall out. The electric router having usurped the name of the original hand tool, the latter must now be distinguished by being called a hand router.

They are usually provided with depth gauges, fences, and variously shaped irons. But one thing these modern tools all lack is the ability to work an area larger than the base that constitutes their sole. Make the added shoe big enough to bridge the workpiece. In the setup as shown, the tool is positioned in the center of the shoe. It might need to be repositioned closer to one end should you need to work into a corner or along an edge. Here are some supplies and tools we find essential in our everyday work around the shop.

We may receive a commission from sales referred by our links; however, we have carefully selected these products for their usefulness and quality.

What Are Planar Graphs Used For Wood Turning Wood Types Calculator Wood Vises For Workbench Zoom Groz Portable Woodworking Vise Us