If so, what size or thread, etc. I put a new one in, just before I e-mailed you. Have a comment on this review? Good tip. Accept Reject. It is mandatory to procure user consent prior to running these cookies on your website.

There are slight differences between my full size lathe and the mini-lathe. The turn off switch is on the right and that is a change from my full sized lathe where it is on the left.

The biggest change is having to move the drive belt every time I want to change the speed of the turning. The covers to access the drive pulley and the motor pulley are on the back and side of the lathe.

To make removal easier I removed the locking screw and put rare earth magnets on the covers. I have used a One-Way four jaw chuck without problems on the lathe. So far I have turned a nostepinne , small cherry bowl, a spinning top , and 5 honey dippers. These are smaller projects and have not worked the mini-lathe hard at all. I am able to turn a very smooth surface indicating that there is very little vibration taking place. So far this Mini Lathe is doing everything I would expect.

I am able to utilize all of the equipment easily and without frustration. The turnings are coming off smooth and easy to sand and finish. Typically, the bed length of excelsior mini lathe levels from to mm. For the identical cause, the suitable distance among the centers of the mini lather must variety from 30 to 36 inches.

The cloth of the bed has to be product of long-lasting materials proposing metal bars and a flat forged bed. Make certain that the headstock is strong and sturdy with first rate amount of spread among the bearings. What Morse cone does this use and what does it weigh??

Great regards, Guillermo. Can jaws be established to this drill out middle? If so, what size or thread, etc. You caught my attention. Since Rockler is one of the major suppliers to woodworkers I thought a review of their Excelsior Mini Lathe MC, exclusive to Rockler was in order. In this review we will also look at the optional bed extension as that is a frequently purchased and equally economical accessory.

The headstock is also made from cast iron and is fixed in place which is a good thing for a mini lathe. This is a Jet Jml 1014 Mini Wood Lathe Review Data manual speed change machine with 5 available speeds: , , , and RPM. And before you vapor lock over the prospect of manual speed changes, they are easy to do especially after you have done it a time or two. I have had both variable and manual speed change lathes and prefer the manual machines like this one because of their ease of use and durability. Once you get used to turning the number of speeds you actually use seems to go way down.

The tailstock taper is self-extracting in that when the quill is retracted fully it releases the tooling without a fight. A four-blade drive spur and a ball-bearing live center are supplied with the lathe. A knockout rod for freeing up the headstock tooling is also included. One of the first things I do with a new lathe is to bring the tailstock up to the headstock to see if the points on the spur and live center match up.

This is critical with any lathe as a major miss alignment here will haunt you as long as you own the lathe. If the Rockler Excelsior Mini Lathe is not actually perfectly aligned the amount of error is way too small to see, even in a close up photo. The spindle is mounted in dual ball bearings and runs silky smooth through all five speeds. A chrome handwheel comes already installed on the outboard Excelsior Mini Lathe Review Journal end of the spindle and makes setup easier. That banjo and the tailstock are both locked in place with adjustable cam action levers.

This is a fast, simple and proven dependable locking system used on lathes of all sizes. Speed changes are accomplished by moving the drive belt on stepped pulleys within the headstock.

The belt is relaxed by adjusting the motor using a front-mounted locking lever. The doors covering the access ports are made of plastic and are removed for speed changes. I know that some will decry the plastic doors but after using this lathe I love them.

Outdoor Woodworking Projects For Beginners Quick Myrtle Wood For Turning 10