Not only do they result in a beautiful pen, but you can get your materials for little or no money. In other words changing the fence position moves the drawer lock router bit setup youtube to position the side correctly, but it also changes how it cuts the tongue, so it compounds the adjustment. I believe that you drawer lock router bit setup youtube use it on any thickness by making the proper adjustments to your router table fence, but Whiteside suggests other bits in their product line for thicker stock. The step where you cut into the fence is to create zero clearance around it. I paid a lot of money for my Jessem fence. With an old handscrew clamp and some scraps of hardwood, you can set up your thickness planer to That really surprised me!

Turn the workpiece around, keeping it face-up, and mill the other end. If you're making more than one drawer, machine all of the drawer fronts and backs, if you like using this setup. We like to rotate the bit so the cutting edge is forward, then lay a straightedge against it for reference, as shown below.

Stand the drawer side on end, placing the inside face against the fence. Use the pushblock, as shown below , to guide the drawer side through the bit. With an old handscrew clamp and some scraps of hardwood, you can set up your thickness planer to Skip to main content.

Drawer-Lock Bit. The one-bit solution to strong interlocking joints. Mill the Fronts The unique geometry of a drawer-lock bit creates a strong bond between perpendicular pieces. Facebook Pinterest Twitter Text. Printer-friendly version. Read more about Doors and Drawers or Routers. Mortising Perfect-fit Box Hinges. What do drawer-slide weight ratings mean? For more related content, subscribe to our newsletter! Keep small cutoffs from escaping at the bandsaw. Pegs provide positive grip on shop jigs.

For more information on Kreg products visit www. Click here to cancel reply. Hi Curtis. I believe that you can use it on any thickness by making the proper adjustments to your router table fence, but Whiteside suggests other bits in their product line for thicker stock. I think it would be really hard for me to cut into the fence for zero clearance. I paid a lot of money for my Jessem fence.

This would mean my fence would be cut for a specific thickness of stock. You can always take the stock Drawer Lock Router Bit Setup Code fence off and replace it, temporarily, with an MDF or melamine shop-made face. This was very useful. Thank you! Hi Dennis. The step where you cut into the fence is to create zero clearance around it. You can use a sacrificial fence for this. A backer board can be used behind the piece as you push it through the cut, which will reduce the chance for blow-out on the trailing edge of the cut.

I would 1st start with a sacrificial fence mounted and then make my adjustments. I would never purposely cut into my Kreg fence! That really surprised me! While your on the subject demonstrate the lock miter bit which is even more fidgety to dial in, accordingly highly recommend using a router lift with a bit height locking feature. Hi Christopher. It is mounted on a shop-made cabinet that George built. I was using my Leigh RTJ They did not recommend using plywood.

He used a zero clearance fence to avoid chipping. Is there something equivalent I could do when cutting my dovetails. Dovetails can look so nice when using baltic birch when it works. Hi Bill. The pin and socket board should, then, be backing up the face of the tail board to help reduce chipping there.

The folks at Leigh are very sharp. It would be worth a call to them to see if they have additional suggestions. In other words changing the fence position moves the groove to position the side correctly, but it also changes how it cuts the tongue, so it compounds the adjustment. Also, changing the bit height not only adjusts the tongue thickness, but it changes where the groove lands on the front, effectively shortening or lengthening the entire drawer box.

All that said this is a great video! For the Baltic birch plywood I see you use, does the shortness of the joint cause a problem with the layers shearing off? I have experienced That little nub is susceptible to breaking off and hence the joint does not hold… any suggestions on how to either reinforce or keep from shearing off? Hello Gene. I regularly test the strength of this joint by flipping the drawer over and standing on the bottom of the drawer.

Even with that kind of stress, this joint stands up every time. Paul Woodworkers Guild of America. I avoid changing the fence position and the bit height at the same times.

I record the bit heights and fence positions for these drawer lock cuts as well as other common cuts in a log book. It is based on the thickness of the front and sides. I measure from the fence to the miter gauge slot in metric. For these types of cuts, I use a designated, one-piece, sacrificial fence that I C-clamp to my regular fence.

That prevents the tendency for the sides to rotate into the bit where the regular fence sides separate when routing a work piece vertically instead of flat on the router table.

Carpenter Block Plane Game Best Rap 2000s Zoom