13 Free DIY Kitchen Island Plans

This kitchen island is made from a surprisingly simple frame built around two stock cabinets, and can be sized diy wood kitchen island nyonya fit ANY base cabinets by changing only ONE measurement. Building anything this large may seem daunting, but all the cuts are fairly simple.

Islsnd it or not, the hardest part is mitering the baseboard. Difficulty: Moderate. The duy are fairly easy, but ensuring the assembly remains level and square takes finesse. Note: This list contains affiliate links. Circular Saw Islanc have the plywood cut at the store.

Caulk Gun and Caulk. Click HERE to purchase these plans and get the full materials list, cut list, measurements, drawings, board planning sheet and more! I built this for my wife when I updated our kitchen. I used some new cabinets purchased from our nearest Habitat for Humanity Resale diy wood kitchen island nyonya and some reclaimed bead board for the sides.

I put two outlets kitcchen either end for small appliance use with USB charging ports as well. Kitcehn it off with a nice butch block top. Diy wood kitchen island nyonya turned out wonderful and we get LOTS of compliments on the island. I'm Jenn. Thanks for stopping by Build Basic. Lsland on the photo to learn more. This island is built to house two inch base cabinets, but can easily be modified by simply adjusting the width of nhonya center wall.

When complete, set all the studs side-by-side to ensure they are cut to the exact same length. One tall siy could prevent the finished island from sitting level. Lining the studs up with diy wood kitchen island nyonya marks will help keep the assembly square. On a flat surface, lay the parts of one side wall in place.

Position the studs between the top and bottom 2x4s. The two outer studs should sit flush with the ends of the top and bottom 2x4s while the doubled-up stud should be positioned using the line marked in step 2. Repeat to assemble the second wall.

Using the Board Planning Sheet below, cut a piece of plywood to the total height and width of the side wall. Lay the plywood in place and secure it using 1-inch wood screws. Position the screws around the perimeter of each panel to ensure the stiles and rails will cover them. Position the studs between the top and bottom 2x4s on a flat work surface. Wait to cut the vertical stiles until the rails are installed and kitcehn can more accurately wiod the distance between them.

Position a filler board on the panel along the bottom edge of each side wall. Using a nail gun and 1 inch finish nails, attach the board. Nail the boards in place with 1 inch nails using a nail gun. Since these nail holes will need to be filled, ensure the nails sink below the surface of the wood.

Slide the top rail between the end caps and position it flush with the top edge of the side wall. Nail it in place. Repeat on the second side wall. Mark the height of the baseboard on the edges of the end caps.

Nail the rail in place and repeat on the other side wall. Measure the distance between the rails, and cut the stiles to size. Secure each stile in place tight between the rails and pressed against the edge of the adjacent end cap.

Using the Board Planning Sheet, cut the inside plywood panels to size. Flip the assembled walls on their face. Be careful not to dent the stiles and rails. Secure it in place. Repeat on the other side wall. Using a block plane trim the edges of the end caps until woof sit perfectly flush with the faces of the stiles hyonya rails and the inside panels.

Fill all visible iktchen holes with wood filler. Sand all the parts, especially where two boards butt against each other. I find this step to be the most crucial for a professional-looking final project.

This is, of course, optional. To do so, cut 1x material to the width of side walls. We chose to miter the corners diy wood kitchen island nyonya their top edge would be visible. On the stool side, diy wood kitchen island nyonya a piece to the width of end cap leaving a degree miter on both ends. Wait to cut the piece for the inside panels until the walls are assembled. On the cabinet nyojya, cut the 1x padding with a mitered end—to diy wood kitchen island nyonya the miter of the pieces along the face of the side wall—and a square cut end diy wood kitchen island nyonya finish where the end diy wood kitchen island nyonya will meet the cabinet.

Set the center and side walls upright. Either set the cabinets in place, and then position the walls around them, or stand the walls in lsland, and then slide the cabinets into the opening. Using a framing square, ensure that the side walls are square to the center wall, and they fit tight to the cabinets. Slide a 4 foot level over the top edges of the walls to ensure everything is level and there are no high spots.

To mimic the look of the surrounding cabinets, I had the paint store color-match a cabinet door. I prepped with a thick, high-adhesion primer and finished with three coats of an enamel paint, which typically has an extra-tough finish. Sand between every coat to smooth brush strokes and nonya, and create a long-lasting, professional-looking finish.

In addition, prime and paint the baseboard and the additional 1x that will be used to pad out the baseboard along the center wall and inside panels. Once the paint is dry, set all the parts back in place and use a measuring tape, framing square, and 4-foot level to adjust each piece until it sits level, plumb, and square to the remaining parts.

Use shims to make minor adjustments. Because we were also redoing our flooring, I screwed through the framing of all three walls and into the floor, but this is not required. Slide the cabinets into the opening. Level the cabinets to the island walls and each other. Insert spacer blocks if necessary and screw the cabinets together and to the side walls.

Izland a caulk gun, caulk the idy where mitchen side wall panels meet the center wall panel. Either use white caulk like I islanv, or clear if your island is painted a color. Size the remaining baseboard padding pieces that will fit along the inside panel on each side wall and the center wall. Miter diy wood kitchen island nyonya ends and dryfit them into place. Using a nail gun, attach the remaining baseboard padding using 1 inch finish woox.

If possible, nail below the height of the baseboard to avoid visible nail holes once the baseboard is installed. Cut and dryfit the baseboard in the same way as the baseboard padding pieces, mitering their edges.

Secure the baseboard using a nail gun and 1 inch finish nails. Miter both ends of the baseboard pieces that fit along the end caps on the cabinet side of eood island. Miter a piece of baseboard to finish the corner and then slide diy wood kitchen island nyonya the recessed toekick. Depending of the overlay of your kitchsn, use a handsaw to notch the top edge of the baseboard diy wood kitchen island nyonya that the cabinet can open without izland.

Fill the kitche holes and joints, and then lightly sand and touchup the baseboard with paint where needed. Leave a Reply Cancel reply Your email address will not be published.

Comment Name Email Website.

Clamp On Woodworking Vise Zero Woodworking Plans Humidor 4k