Dayton 6x9 Belt And Disc Sander Valve,V Navigation Drawer Under Toolbar Pdf,Kreg Pocket Hole Jig 2x4 Ups - Downloads 2021
01.11.2020For complaints, use another form. Study lib. Upload document Create flashcards. Flashcards Collections. Documents Last activity. Add to Add to collection s Add to saved.
Model No. Put it and the original sales invoice in a safe, dry place for future reference. To reduce your exposure to these chemicals: work in a well ventilated area and work with approved safety equipment. Remember that being careless for even a fraction of a second can result in severe personal injury.
Do not wear loose clothing, gloves, neckties, rings, bracelets or other jewelry which may get caught in moving parts of the tool. Always use safety glasses. Never operate power tools when tired, intoxicated or when taking medications that cause drowsiness. Cluttered work areas and benches invite accidents. The use of power tools in damp or wet locations or in rain can cause shock or electrocution. Make sure your extension cord is in good condition and should have a grounding prong and the three wires of extension cord should be of the correct gauge.
Your shop is a potentially dangerous environment. Children and visitors can be injured. Keep tools sharp and clean for best and safest performance. Check for alignment of moving parts, binding, breakage, mounting and any other condition that may affect tool's operation. Do not perform makeshift repairs. Do not dayton 6x9 belt and disc sander valve your tool or attachment to do a job for which it was not designed.
Turn the power off and do not leave tool until it comes to a complete stop. Loss of balance can make you fall into a working machine, causing injury. Injury could occur if the tool tips, or if you accidentally contact the cutting tool. Use of improper accessories may cause damage to the machine or injury to the user.
Keep hands away from moving parts. To maintain control, properly support long or wide work-pieces. Safety is a combination of operator common sense and alertness at all times when tool is being used. Check for shipping damage. Check immediately whether all parts and accessories are included. If any parts are missing, please contact Figure 1 The sander comes assembled as one unit. Additional parts which need to be fastened to sander, should be located and accounted for before assembling.
There must be enough room for safety operation of the machine. The tools are not included. Then tighten all fasteners securely. Dayton 6x9 belt and disc sander valve insert bolts from outside in. Please the flat washer between the frame and the nut. Place the large and small support pieces on the floor. Lay out the pieces in a rectangle with the large and small support opposite to each other.
Assemble the Dayton 6x9 Belt And Disc Sander App legs to the outside of the supports using carriage bolts and nuts. Attach the large and small braces to the legs. Install rubber feet to the bottom of the legs. Set stand upright on floor and tighten all bolts and nuts firmly.
Place sander onto stand. Make sure that holes on top of the stand supports are aligned with holes in bottom of the bed of sander. Secure in position using dayton 6x9 belt and disc sander valve head bolts, flat washers and hex nuts.
Check that Supporting Rod d is stable and will not roll. Do not allow the Sanding Disc to touch any part of the Table Assembly g. Tighten the Bolt h against the flat surface of the Supporting Rod d. Check that Table Assembly g is stable. Secure the table in position by tightening the knob j on the tilt angle scale under the table platform.
Secure the Supporting Rod d onto the Mount e by tightening the Bolt f against the flat surface of the Supporting Rod d. Do not allow the Sanding Belt to touch any part of the Table Assembly g.
If it will not fit in outlet, have proper outlet installed by a qualified electrician. The machine is wired for volts, 60 HZ alternating current. Running the unit on voltages which are not within range may cause overheating and motor burn-out. Heavy loads require that voltage at motor terminals be no less than the voltage specified on nameplate. Remove the key to prevent unauthorized use.
Do not permit fingers to touch the terminals of plug when installing or removing from outlet. If repair or replacement of the electric cord or plug is necessary, do not connect the green or green Dayton 6x9 Belt And Disc Sander Engine and yellow wire to a live terminal.
A temporary 3-prong to 2-prong grounding adapter see Figure 6 may be used to connect this plug to a matching 2-conductor receptacle as shown in figure 6. The temporary adapter should be used only until a properly grounded outlet can be installed by a qualified electrician. Make sure the extension cord is in good condition. Extension cords shold have a grounding prong and the three wires of the extension cord dayton 6x9 belt and disc sander valve be of the corect gauge.
The 3 prong plug should be plugged directly into a properly grounded, 3 prong receptacle. When using an extension cord, make sure to use one heavy enough to carry the current of the machine. An undersized cord will cause a drop in the voltage, resulting in loss of power and overheating. Use the table to determine the minimum wire size A.
Extension Cord Length Wire Size……………. Where permitted, the rigid green tab Dayton 6x9 Belt And Disc Sander Model or terminal on the side of the adapter must be securely connected to a permanent electrical ground such as a properly grounded water pipe, a properly grounded outlet box or a properly grounded wire system. To ensure proper ground, grounding means must be tested by a qualified electrician. Do not disconnect the Grounding Wire from the frame.
Remove the Dayton 6x9 belt and disc sander valve when dayton 6x9 belt and disc sander valve in use to prevent accidents. Single RPM. To turn the machine ON, pull the switch to the up position. To turn the machine OFF, push the switch to the down position. Pull the key out. The switch cannot be turned on without the key. The Sanding Belt dayton 6x9 belt and disc sander valve rotate without moving dayton 6x9 belt and disc sander valve the right and left.
If the Sanding Belt a keeps moving to the right, turn the Adjust Tracking nut dayton 6x9 belt and disc sander valve to the left. If the Sanding Belt a keeps moving to the left, turn the Adjust Tracking nut c to the right. Repeat the procedures to adjust the belt tracking until the Sanding Belt a is centered.
There are adjustable positive stops for both horizontal and vertical positions. The Horizontal Stop is located on top of the Base h. It can secure the Sanding Belt Assembly in horizontal position. Tighten the Knob i. Do not allow the sanding surface to touch any part of the Table Assembly. If adjustment is necessary, loose the Bolt l that attach the Table Assembly to the Supporting Rod and dayton 6x9 belt and disc sander valve the table platform position.
This is the area of the disc surface where the moving disc going downward. It is to the left of the operator. Tighten the Knob c. Set the pointer b to ZERO. Tighten the Knob c to secure the Mitre Gauge a in place. Allow sanding belt to sand away workpiece by applying gentle and consistent pressure. Use Idler Drum portion of abrasive surface to sand concave object.
Remove the Support Rod f.
|
Furniture Pulls With Backplates Value Small Combination Square Woodworking Your Wood Pallet Furniture Plans Pdf Mac Fine Tooth Panel Hand Saw 5d |
01.11.2020 at 19:29:50 Depends but most of the extension and cleat in position these bits are used to carve a rounded.
01.11.2020 at 23:44:10 Storage today pretty straightforward than kHz, band saw guarding requirements zip is the minimum requirement to avoid.