That can be used to adjust the front of the saw table where the fence will be positioned so it is exactly 90 degrees blave the travel of the motor and yoke on the saw arm. Saw is not mounted securely. Firmly bolt the saw to the leg stand to keep the saw from tipping, walking, or sliding. Because the teeth are pointing up on that side, you'll have to put more pressure on the wood 10 inch radial arm saw blade youtube steady the blade. If I use the screw clamps then the rails will be just perfect. I have had this raadial 40 years.

Register for a new account. Anti-bot validation. Sign in. Remember me. Woodworker II - Thin Kerf. Woodworker II - 48 Tooth. Woodworker II - Modified. Product Shipping Information. Please Note before you place your order: we are experiencing shipping delays of up to 5 months. If you need a blade faster than we can provide it, we recommend you note the blade's catalog number and do an online search for a Forrest dealer near you.

Catalog No. Add to cart. Description Features. Material: Hardwood Ply veneers Plywood Softwood. Saw manufacturer: Dewalt General Sears. Blade specifications Diameter: 10". Teeth: Keep the saw power off until you are ready to use it. It should be connected to a power supply that is volts, 60 Hz, AC only normal household current. It 8 Inch Radial Arm Saw Blade Edition should be connected to a volt power supply only If It has been reset according to the instructions in this manual. Your radial saw has been set up at the factory to operate efficiently on a V AC single voltage circuit.

However, if heavy duty operation is required, the circuits are overloaded, or the circuit is low voltage, have a qualified electrician change the voltage on the main power system to a V AC voltage circuit. Page 10 A type of rip cut in which the motor is between the blade and the column. The blade is "outside" the motor. Pushatlck A device used to feed the workpiece through the saw blade during cutting operations.

It helps keep the operator's hands well away from the blade. Rabbet A type of cut that gives a notch in the edge of a workpiece. Page 11 Also, the workpiece area which will be or has been cut by the blade. The distance that the tip of the saw blade tooth is off set from the face of the blade. Page 12 A, Handwheel Star Washer Hex Key A.

Hex Key Page 13 Check all loose parts from the box with the list below. Use the instructions on the following pages to assemble. All fasteners are shown actual size. Saw Assembly not shown Leg Stand Assembly not shown Page 14 Check all loose parts from the box with the list below, Use the instructions on the following pages to assemble.

Table Support A. Table Support Rails Page 15 The following tools are needed for assembly and alignment. They are not included with this saw. The arm can be raised or lowered to change the blade height or swiveled left and dght for a miter cut. A yoke fits into a carriage on the arm, which can travel back and forward. Page 19 See Figure 9B. Blades recommended for other operations are listed in the Accessory section of this manual.

Page 20 Located on the left side of the arm on the cardage cover. See Figure 9C. The powerful induction motor has a capacitor start. It is mounted in the yoke and rotated with the bevel index knob and bevel lock lever.

See Figure 9B. Page Loose Parts List Assembly is best done in the area where the saw will be used. When you remove the saw and hardware from the packing materials, carefully check the items with the Loose Parts list. If you are unsure about the description of any part, refer to their illustrations. For your convenience, all fasteners have been drawn actual size.

Page 24 Iockwasher. Do not risk serious injury or damage to the saw by failing to replace these parts. There are holes in both sides of each support. The long side of each support with the slotted holes fits against the saw base. The yoke clamp keeps the yoke from rotating on the carriage when you want the saw blade to be station- ary. Use this procedure to check and set the yoke clamp. The bevel lock lever locks the blade at desired angles other than the preset positive stop 8 Inch Radial Arm Saw Blade Test angles, The bevel lock lever is preset at the factory but may need readjustment after shipping or extended use.

Check for overtightness or looseness and make any neces- sary adjustments as follows There should be no play, vertical or horizontal, in the arm relative to the column.

If you can move the arm up, down or sideways when it is unlocked, use the following steps to tighten it. Page 29 Recheck the rotation by holding the front of the arm, grasping the top of the column support with the other, and pressing the arm to the side.

Page 30 Loose carriage bearings permit the blade to wander slightly while cutting, which will result in a poor cut and more wear and tear on the saw.

Use the following steps to check for tightness and to then adjust the bearings if needed. Page 31 Move the arm to the opposite side and repeat the above procedure. When the opposite side is level, recheck the first side to make sure that it is still accurate and even. Line up the hole in the U-clip with the saw base hole just to the left of the center notch in saw base.

See Figure 23B. Page 34 See Figures 26A and 26B. Place the inner blade washer, saw blade, outer blade washer, and blade nut on the blade arbor. See Figure 26A, Note: The conca've side of blade washers go against the blade. When ripping the riving 8 Inch Radial Arm Saw Blade Model knife must be centered with the blade to ride in the middle of the kerr and keep it from binding. Binding pinches the blade. Blade pinching can cause kickback. There are two pairs of anti-kickback pawls.

Page 36 The control cut device offers many benefits. As it increases operator control, it eliminates the risk in a cross cut of the saw "climbing" out and over the workpiece at the operator. Feed control of the blade as it cuts through the workpiece increases, as does the accuracy of the cut. Page 37 0" and leave it unlocked. Lock the yoke lock handle right side Negative Rake Radial Arm Saw Blade Video of saw, below yoke and the bevel lock lever.

Page 38 Place the square flat against the blade between two teeth. Page 39 The blade must be angled at 90" to the fence when the handle is at the front of the saw.

If not, kickback could result during a cross cut. Kickback can cause serious injury by throw- ing the workpiece toward the operator. In addi If you can see a gap, adjust the blade to be at 90" bevel to the table with the following steps. The rip scale indicators on the arm show the distance between the blade and the rip fence.

The upper scale is used when the fence is positioned directly behind the front table. The lower scale is used when the fence is at the extreme rear, directly in front of the column. Page Labels The control cut device offers many benefits. It can make dado or molding cuts with special attachments.

Woodwork Nursery Furniture Network Window Frame Router Bits Linux