Manufacturers Index - Darra-James Corp. Member Profiles. Machine Registry. Donations to Vintage Machinery. All rights reserved. The VintageMachinery.

On my DW I extended the table to the left and and added an extra triangulated support. I have a manual in pdf if you want and can send you the pages you need for the table. The table is three pieces so you can move the fence for wide rip cuts. Cheers conwood. Thanks for the great advice everyone. Sorry I am a little slow responding.

We have made and fitted a table using MDF as suggested. All is good I have emailed the Toolkraft website, but there has been no reply as yet. I would really like to see the DeWalt manual , especially the 3 piece table.

You can email to dcoles removethisbit bigpond. Thank you in advance. Once again thanks for all the advice. Hi Avery, Entire manual on its way via email. Cheers, conwood. Join Date Aug Location melbourne Posts 2. I need to build a stand, top and set up true. Any chance of you might send me a user manual pdf too please if not too much trouble, Regards, Justin.

Toolkraft Radial arm saw Hi Guys I need some help with Toolkraft Radial Arm Saw Control more information on this saw as I have just bought one, to go and do some work in the Cape on a house we bought down there. It is still in good working order but I'll need to refit a table and true up the blade some. It seems to be one of the issues with these saws if you want to do neat work.

Regards Deon. I suggest this because there is a reasonable amount work involved in getting the table spot on relative to the blade, and it is easy to mark the top and disturb the setup once you start making compound cuts, ripping etc.

Then the saw looses it potential accuracy unless you are willing to spend another load of time resetting a new table sheet, and a lot of people can't be bothered making the effort. I make my torsion box around 50mm thick with inbult mounting hardware for the brackets etc, and 10mm skins. I then top the torsion box with a 6mm hardboard sacrificial surface that can be swapped out in under 5 minutes when needed. This enables me to spend a couple of hours once getting the table spot on, knowing that it will maintain the setup through seasons etc, and that the surface can be replaced as needed without loosing the setup.

From the pics of the ToolKraft, I am seeing brush holders at the back end of the motor, so it uses a brushed universal motor. However I doubt that the rear power takeoff is suitable for mounting router bits as the motor speed would be too slow to be practical if safe for inch diameter saw blades.

The DW uses an induction motor at RPM depending on mains frequency and the PTO is provided for other accessories and drilling, rather than routing. However I have seen articles where people have fabricated a bracket to mount a router to the side of the carriage for routing dados etc.

I used to be an engineer, I'm not an engineer any more, but on the really good days I can remember when I was. Hi all, I have been given a Toolkraft 10" radial arm saw x which needs some work as it hasn't 8 Inch Radial Arm Saw Blade Model run for a few years, from reading this thread can someone help with a manual Dewalt Radial Arm Saw Model Numbers Ios for this saw, any help much appreciated. Hi John, I have a dewalt manual which will help. Alternatively you may call in and have a look at the saw.

Page 1 of 2 1 2 Last Jump to page:. Discussion Forum. Machine Info. Photo Index. Support Vintage Machinery. Submitting Content. Contact Us. Discussion FAQ. The Shop. Projects Forum. For Sale Forum. Manufacturer's Index. Machine Registry. Photo Index Home. Index by Manufacturer. Index by Machine Type. Recent Submissions. Submit New Photo. Classified Ads. Vintage Machinery Store. Workshop Calculations.

Patent Search. Book Store. Member Profiles. Highland Woodworking. Publication Preview. View PDF 3.

Cupboard Door Hinges Wilko Lyrics Used Chain Mortiser For Sale Craigslist Case Powermatic Benchtop Mortising Machine Ui