For Sale Forum. I did it even though I fitted my saw with some bungie cords, just to be certain that the saw was safe in accordance with their recomendations. If they do not supply the safety kit anymore then use a bungi cord and attach it to prevent the blade from crawling forward. Sears Roebuck introduced wood-working machinery in their catalog, according to one source. The Craftsman trademark was registered by Sears on May 20, A scrap piece of material may have wedged old craftsman radial arm saw troubleshooting list up in the saw, causing the motor to grind or wheeze when the machine is powered on. Manufacturer's Ood.

By no means is it used and abused, unsafe maybe Other than cleaning up the track and adding some new grease, it would continue to serve me fine as long as I am as careful with it in the future as I have been in the past 24 years.

The smart thing to do would be to take the money and invest in a new miter slide saw maybe. Hi Robert I am glad you have the option rather than get nothing and still have a dangerous saw. I did the retrofit but did it about 2 years ago.

I did it even though I fitted my saw with some bungie cords, just to be certain that the saw was safe in accordance with their recomendations. I also got a better blade cover and a new table top. In your case it is a toss up as I also have the Hitachi 12" slide saw and now about the only thing I use the radial any more is for building custom molding like the dental molding that is common but expensive to buy.

Robert Wolff said:. Sign Up or Sign In. For Technical Support, please call or send a message. Added by Mike Criss. Added by Alex DrMaster. Added by Philip Miller. Just got a rip-cut and installed my Bosch saw haven't used it yet but saw was a good fit. Got the original ripcut and didn't really like it had trouble cutting straight.

New one has several improvements should make it work much better. Is the screw driver impact drill rated? Posted by Duke Leon on February 15, at pm. Several months ago, I purchased the Kreg K4MS so that I could build the Lego Table as outlined on the companion "buildsomething" web site which exclusively uses pocket hole construction. I have considerable experience with conventional….

Posted by Robert Ringel on September 17, at pm — 4 Comments. Powered by. All Discussions My Discussions Add. Is there a way to clean the components and what is used to lubricate the track??

Replies to This Discussion Permalink Reply by Ken Darga on June 30, at pm You can obtain a manual by contacting Sears-Craftsman, with the model number and serial number, from the nameplate on your machine.

Old grease gums up and hardens, making some mechanisms difficult to function properly. Use a solvent degreaser to remove all the old lubricant and apply applicable suitable lubes. You can obtain the degreasers from an auto supply store. Thanks Ken Ken Darga said: You can obtain a manual by contacting Sears-Craftsman, with the model number and serial number, from the nameplate on your machine. By the way Ken is percent correct on the grease and care of the saw.

Robert here is the article I wrote: Comment on: Topic 'table vs radial saw' e magazine, world wide. You guys are wonderful, thanks again!! Robert Wolff said: In doing a search for the recall on my specific saw You guys and this forum have been very helpful. Thanks Again. Need Help? How about don't put your freaking hands in the way!

I used the heck out of my Dad's saw while I was growing up. Very handy tool. I used it more than a table saw.

Pallet Pete , Jun 28, From what you describe, you're getting power to the motor, so the switch is probably fine. If the armature spins freely your bearing are probably OK. I'm guessing you need a new set of motor brushes This is just a SWAG though Alright finally here are some pics of the saw in question.

Pallet Pete , Jul 2, Last edited: Jul 2, HDRock , Jul 2, Used one of those in the wood shop in college. I was thinking slide miter till someone referenced a slide miter in a post then I saw the pics and realized what y'all were talking about. If you have been working on a large project or working with tougher stock you may find that your motor may stall. Just meaning that it stops. It will need to cool down in order to be able to start up again.

Try replacing your blade. A sharper blade will be more efficient for the motor. If your motor keeps stalling then it might be warning you that the time for replacement is near. There are really not too many problems that you can have with your radial arm saw motor. You can replace a few of the parts over time, and make sure that you are cutting with a sharp blade, but when the time comes for replacement you may just need to give in.

Unless of course you are a skilled rebuilder of all things electrical. We welcome your comments and suggestions. All information is provided "AS IS. All rights reserved. You may freely link to this site, and use it for non-commercial use subject to our terms of use. View our Privacy Policy here. Toggle navigation subscribe. Written by Doityourself Staff. Basics First Before getting into some more serious problems you will Old Craftsman Radial Arm Saw Troubleshooting Site want to check the easy things first.

Related Posts Vintage radial arm saw worth keeping?

Butler Tray Hinges For Sale 10 Cnc Woodworking Machine Tools Not Working