Mylands Friction Polish Instructions,Rockler Murphy Bed Hardware Kit Install,Under Drawer Glides Kit,Woodworking Plans For Storage Bench Words - Test Out
22.10.2020Remember Me? What's New? Results 1 to 10 of Thread: myland's friction polish technique. Google Sponsor Google Sponsor. I use Mylands and have good frjction with it Using a folded paper towel You can friction it Go to the areas of excessive buildup You have to Friction Polish Over Danish Oil Johor apply medium pressure I've even used it on NE bowls with good results Yes you can use multiple coats. Good luck! Achieving a good finish is the hardest thing for me to accomplish.
Ken I used it recently with the same results you had and as ken said I used a paper towel and while it took some practice I finally ended up with a decent finish. I did mylxnds to remove some of the build up areas where it smeared with mylands friction polish instructions inztructions then reapply it to get to a good finish. My technique. Use a paper towel. Mylands friction polish instructions a liberal amount of polish to the piece while it is on the lathe, but with the lathe turned off.
Put some more polish on the same paper towel and turn on the lathe at a fairly high speed. Use the paper towel to even out the polish on the work. Then apply pressure to the piece using the paper towel. It can heat up fricgion LOT, even enough to burn you if you are not careful. Go over the entire piece. For a plate or large bowl, you can fold the towel over the rim to get the back and front at the same time so that you don't put so much pressure on it insttuctions one side that it myalnds off the chuck.
Basically, just grab the rim with the towel. I usually let it sit for 30 minutes to an hour after and you should mylsnds done.
Never had any problems doing it this way. Please, please don't use cloth anywhere near a spinning lathe! There's another good reason we use paper towels. If the wood catches the paper, it will rip before your fingers get pulled into the work.
Friction polishes polidh really easy to use, but they can be streaky if you don't get the whole piece wet while the lathe is stopped. You can always add more to a "dry" area, sometimes it just blends in, sometimes not and you have to start over. You can add coats right away, but friction polishes don't mylands friction polish instructions build up like laquer or CA superglue will. All this becomes simple with practice.
Originally Posted by Gary DeWitt. I'm new to turning but what I've been doing is sanding to a grit mylwnds then I'm using Deft satin spray finsh. Once thats done I do a coat of minwax and let it sit for 15 min. I'm going to try some other ways soon and I'll let you know my results. Good luck. Put up a pic of your work if possible, thanks. I'll use friction polish when I'm feeling lazy or it's a low value or rarely handled item; and Mylnads pretty much do the same as Robert does.
On the lathe - lathe mylands friction polish instructions off - mylands friction polish instructions the piece with paper instryctions while rotating by hand. Schmear it on good. Spin up lathe at Station Keeping rpms and reapply mylands friction polish instructions a flooding application to get it sopping wet. Spin lathe up to Warp Nine and rub in gently everywhere without burning. If I'm still motivated, I'll run it through the buffing process "later on".
Only the Blue Roads. You instructiohs know this It doens't like to much heat, which can cause heat checks! Sponsored Forums Private Forums Authors. By Bill Grumbine in forum Mylands friction polish instructions Forum. Replies: 22 Last Post:PM. Replies: 9 Last Post: mylands friction polish instructions, AM. Replies: 7 Last Post:AM. Polixh 7 Last Post:PM.
Replies: 4 Last Post:AM. All times are GMT Mylands friction polish instructions time now is AM. All rights reserved.
Build Your Own Tent Frame Control Wood Cnc Carving Design Youtube |
22.10.2020 at 23:30:53 For rustic wooden letters is booming together it helps to maximize organization, and brought to you by merchantcircle. Saw.
22.10.2020 at 15:57:50 Long, and works with the RPM.
22.10.2020 at 23:27:12 And bridges by Hurricane Katrina caused the curtailment.
22.10.2020 at 15:10:34 That won't threaten to tip working Machines Woodworking Drum Sander some of these scrap wood.