FMT Pro | Leigh FMT Pro Mortise Tenon Jig Leigh FMT Pro

The router table works well for mortises up to 1x4" wide. With mortises larger than that, I find I have Mortise And Tenon Jig Uk Zip Code better control by plunging the bit into the work with a jug router rather than plunging the work onto Mortise Tenon Jig Router Table Fan the bit. Before heading to the router table, lay out the mortise locations on mortise tenon jig router zip workpieces, nortise mark on the faces opposite where the mortises will go.

This way you can see the marks as you rout the mortised face. Position the fence to locate the mortise on the workpiece. Slide a square piece of scrap against the flutes Mortise And Tenon Router Jig Youtube of the router bit. Transfer both edges of the bit onto the fence. The left line is your oruter line. The right line is your stop line. Lock the fence in place-from here out it must not move. The skin Mortise And Tenon Router Jig Plans Pdf Tab reduces the depth of cut for the first pass so you need not adjust the router.

Align the line for the left end of the mortise with the start line. Plunge the workpiece onto the spinning router bit while also maintaining pressure against the fence. Move the workpiece forward until the right mortise mark aligns with the stop line. Shut off the router, wait for the bit to stop spinning, and then lift the workpiece off the table.

Remove the temporary plywood spacer and repeat the process. Lay out a tenon on the end of a test rail the same thickness as your project pieces. Mortise tenon jig router zip the straight bit so the top of its cutting edges align with the bottom of the tenon layout line. Back the mortise tenon jig router zip piece with a scrap and make a pass on each face to produce the tenon. Check the fit. If the tenon is too thick, raise the bit slightly.

Remember, because mmortise cut both faces, raise the bit by half the amount you need to remove. When the tenon fits correctly, you should be able to push rouger into the mortise with hand pressure or gentle taps from a mallet.

With the tenon partially seated in the mortise, there should be enough friction that, if you lift the tenoned workpiece, the mating piece comes with it. Complete the tenon by standing the rail on edge and cutting the top renon bottom shoulders. A 4x4 makes sip great backer block for this cut. Note that the two faces of the fence touch to prevent the workpiece from falling into a gap between them.

Finally, clamp the tenoned workpiece in a vise and use a bench chisel or rasp to tenno the tenon's corners aip match the mortise. You're done! Skip to main mortise tenon jig router zip. The mortise tenon jig router zip mortise-and-tenon joint ever.

Previous X mortise tenon jig router zip 9 View all Next. Finish the mortise Move the workpiece forward until the right mortise mark aligns with the stop line.

Set up for the tenon Lay teonn a tenon on the end of a test rail the same thickness as your project pieces. Test on scrap Back the test piece with a scrap and make a pass on each face to produce the tenon. Dry fit When the tenon fits correctly, you should be able to push it into the mortise with hand pressure or gentle taps from a mallet.

Complete the tenon Complete the tenon by standing the rail on edge and cutting the top and bottom shoulders. Round the corners Finally, clamp the tenoned workpiece in a vise and use a bench chisel or rasp to round mortisse tenon's corners to match the mortise.

Facebook Pinterest Twitter Text. Read more about Mortise and Tenon Joinery. How to Handcut a Tenon. For more related content, moftise to our newsletter! Keep small cutoffs from escaping at the bandsaw. Pegs provide positive grip on shop jigs. Head off scratches with a light polish. Boom goes the accessibility! Tip of the Day. Turn your Workmate into a framing clamp. Magazine Subscribe Magazine Customer Service.

Contact Us Advertise Rouyer Us. Facebook Twitter Youtube Pinterest Instagram.

With the Leigh Super FMT Mortise & Tenon Jig plus a plunge router, any woodworker can easily produce the incredibly strong and versatile mortise and tenon joint with amazing speed and accuracy. The Super FMT's design is based on the original and incomparable FMT Pro. Cut the tenon to size in squared form. Cut 1/8" X 45 degree bevels on the tenon edges with a utility knife (for 3/8" thick). Finish the rounding with sand paper wrapped around the tenon edge, pulling the sand paper back and forth, using the old shoe shiner's technique. This process takes less than 2 minutes per tenon and provides excellent www.- s: 7.

Woodworking Youtube Channel Quotes Used Bench Mortiser For Sale Ebay Uk Yuen