mastercraft belt sander | eBay

D]sc Sander Everyday AssembJy and Adjustments Safety Goggles are available Maintenance READ and become familiar with this entire instruction Parts LEARN the tool's applications, limitations, and possible hazards. Use clamps or a vise to hold work when practical.

It's safer than using your hand and it 3. Form the habit of checking to see that keys and adjusting wrenches are removed from the tool before Don't use power tools in damp or wet locations, or expose them to rain. Keep work area well lighted. Consult the BELT Connect to a V, 15 amp branch circuit. To a safe distance from the work area.

Serious injury could occur DISC YES be carefully checked to determine that it wilt operate attachment to do a job for which it was not designed. Check for I0. Make sure your alignment of moving parts, binding of moving parts, extension cord is in good condition.

When using an breakage of parts, mounting, and any other conditions extension mastercraft belt and disc sander manual website, be sure to use one heavy enough to that may affect its operation. A guard or other part that carry the current your product will draw.

An undersized is damaged should be properly repaired or replaced. Don't leave the tool until the correct size to use depending on cord length and nameplate ampere rating. If in doubt, use the next it comes to a complete stop. Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known [to the State of California] to cause cancer, birth mastercraft belt and disc sander manual website or other heavier gauge.

The smaller the gauge number, the 2t. Keep proper footing and heavier the cord. DO NOT wear loose Wear protective Your risk from these exposures varies, depending on how often you do this type of work. To reduce DO NOT use power tools in the presence of flammable hair covering to contain long hair. DONOToperate thetoo! If a properly grounded Dustgenerated fromcertainmaterialscanbe DO NOT sand pieces of material that mastercraft belt and disc sander manual website too small to current and reduces the risk of electric shock.

Atways operate the be safely supported. The plug ungrounded receptacle. The temporary adapter should be for proper dust removal. Use dust collection systems! KEEP fingers away [rom where the belt goes into the MUST be plugged into a matching receptacle thai is used only until a properly grounded receptacle can be whenever possible.

WHEN sanding a large workpiece, provide additional local codes and ordinances. If it will not fit the grounded receptacle box. The Canadian Electrical Code DO NO'[' sand with the workpiece unsupported.

Support the workpiece with the backstop or table. The qualified electrician. CAUTmON: In all cases, make certain the receptacle in only exception is curved work performed on the outer question is properly grounded.

The according to the instructions, and until you have read and Do not. Mastercraft belt and disc sander manual website or grinding the table, backstop or belt before turning the sander terminal.

Fig, A workpiece. Operating you do not completely understand the grounding instructions, 2, table while the sander is operating.

Solvents coutd dissolve or other wise damage the material. Properly Grounding Prong Grounded or fai! See directional arrow on back of belt. When using an Keep cords away from heat, oil and sharp edges. An undersized cord wilt belt does not run off the pulleys.

The table below shows the correct size to use I ake Sure This torn, loose. Use only correct size sanding belt and disc. When using the bett to grind or sharpen metal or depending on cord length and nameplate ampere rating. If 2-Prong Narrower belts uncover parts that could trap fingers. The smaller the gauge Receptacle number, the heavier the cord.

Never use a steady the part of the workpiece to be sanded. Dip or quench Be sure your extension cord is properly wired and in the workpiece in water Io cool it.

Always replace a damaged extension cord This tool must be grounded while in use to protect the 9. Move or have it repaired by a qualified person before using it.

Keep hands away from sanding belt or disc. Sand Protect your extension cords from sharp objects, excessive meta the material across mastercraft belt and disc sander manual website abrasive and al!

Before connecting the motor to 0 6 18 16 16 14 Sanding on t0 t2 16 16 14 12 the upward side of the disc Mastercraft Belt And Disc Sander Manual 2019 could cause the workpiece current stamped on the motor nameplate. Running at a lower voltage will damage the motor. Disc 1 C. Disc table 1 E. Follow instructions that accompany accessories.

Disc dust chute Belt dust chute. H, "Fable support rod 1 I. Hex key 1 K. Hex head bolt t M. Long pan head screw 40mm 1 o Adhesive-backed Discs 6 inch: N. Large washer 1 Bett tracking knob R. Sears may recommend other accessories not listed in this manual.

Remove this coating with a soft cloth moistened with WD G Attach pulley cover 1 using the 40mm Mastercraft Belt And Disc Sander Manual Yoga long mastercraft belt and disc sander manual website head Remove and clean any adhesive or material left on the screw 2 and 12mm pan head screw 3as shown.

Peel plastic backing from abrasive disc 1 Tighten screws securely. For your own safety, never connect plug to power source outlet until all assembly mastercraft belt and disc sander manual website adjustment steps are completed, and you have read and understood the safety and operating instructions.

Slotted screwdriver 2. Loosen mastercraft belt and disc sander manual website nut 3and belt tension set screw 4 by turning it counterclockwise.

Phillips screwdriver Level 3. Raise up on the motor pulley 5 to replace or remove the existing belt. At the same time tighten set screw 4 by 1. Turn clockwise to tighten. Reapply light pressure to the belt and maintain belt 2. Position disc cover 1 in place as shown. Stide disc plate onto shaft until 2. B it does not require excessive tension to function disc plate mastercraft belt and disc sander manual website and edge of the pulley cover are Fig.

Insert hex wrench, down through slot 4 in the top of belt and pulley guard and tighten set screw I against 1. Bolt 4 position sanding arm 2 in the horizontal position by 3. Rubber washer 1 mUm I I 5. Flat washer 6. Worksurface Lockwasher t J- 9. Hex nut Jam nut i 5.

Mastercraft 4 x in Belt/Disc Sander features a amp motor with ½-hp 4 x 36" (10 x cm) sanding belt/5(). Mastercraft Belt And Disc Sander Manual Find Mastercraft Belt Disc Sander in tools / Buy or sell tools in Ontario Mastercraft belt sander 16' combo felt and disc sander. Includes Instruction Manual. 4' x 36' belt operates at 1, FPM, 6' disc operates at 3, RPM, Includes, a miter gauge, grit sanding belt and grit sanding disc, 2-year. 1 product rating - MasterCraft Belt/Disc Sander MOTOR BELT Model High Power USA Polybelt. C $ Top Rated Seller Top Rated Seller. Buy It Now. Orig Mastercraft Belt Sander Owner's Manual/Parts List Eng/Fr Model Pre-Owned. C Missing: website.

Best Wood Carving Knife For Beginners Tab Best Wood Router For Beginner Exam Build A Bear Toy Story Outfit Test Diy Wood Sanding Machine Instructions