JET® 6" Deluxe Wood Jointer with Quick Set Knives | JET® Woodworking Machines

They offer a tried and tested cast-iron design of solid quality for a reasonable price. However, JET makes four jointer models and the differences between them are not always obvious. We will take jet 6 inch jointer planer queue look at each of the four models to determine how they jet 6 inch jointer planer queue different, which ones may be better or worse, and which machine may be right for your jet 6 inch jointer planer queue situation.

They are identical, except for the cutterhead. The jointers have extra long cast iron infeed and outfeed tables. Longer tables help significantly with keeping long workpieces perfectly flat.

The tables are mounted to the frame with a classic dovetail also called wedge-bed system, which means they slide at an angle over a dovetail jet 6 inch jointer planer queue extrusion.

This is a classic design already used for many years throughout the industry. There is a minor disadvantage to this dovetail design, which is that it can start to wear slightly over time, making it harder to set the two tables in one plane. However, this wear will take a long time and even then it is questionable how big an impact it will have.

However, if you do not want to take this risk, take a look at jointers with a parallelogram base design. For both the infeed and outfeed table there is a chrome handwheel mounted on the frontrather than below the tables. This makes it easier to reach in and comfortably change the height of the tables.

On some jointers or jointer planer combos the fence can be a bit flimsy, and manufacturers seem to think of it as an easy component to save costs on. However, if you want to joint accurate degree edges on your boards which is really an essential feature of a jointer you need a solid fence.

Luckily JET provides sturdy fences which are secured well in the middle. The fence has 3 positive stops for 45 degrees left and right, and 90 degrees. This allows you to much quicker get the right setting, whether you want to jet 6 inch jointer planer queue create a straight edge or joint miters. The guard used on the machines is a classic American-style spring-loaded pork-chop cutterhead guard that moves out of the way when you push against it with jet 6 inch jointer planer queue workpiece.

It will depend on your personal preference whether this is a good or a bad thing compared to a Euro-style blade guard for example. The machine also has a rabbeting ledgewhich is not frequently used by most users, but it is a nice additional feature to have. However, you may find that you need to keep your blades sharp to maintain enough power to joint hard and difficult boards. On to the differences then. How do they work and is the upgrade worth it?

The quick-set blades of the JET JJ-6CSDX are similar to the standard classic straight knives found on many jointers — 3 straight knives that need to be set at the same height.

Because each blade has identical holes, if you swap out the blades it will set itself in exactly the same position jet 6 inch jointer planer queue the previous blade. The result is that you only need to set your blades to the right height once. This is a great time and annoyance saver. Each blade has 2 sharp edges, so you can flip it over when one side gets dull.

Helical or spiral cutterheads have many different carbide cutter inserts instead of three straight knives. These cutters are positioned in a spiral shape around the cutterhead.

Each cutter can be loosened individually and has four sharp sides. This system has a several useful advantages: Jointing makes less noise, the jointed surface looks better, the cutters are easier to replace when damaged or dull, and last much longer.

Because each cutter can be loosened and replaced individually, if you hit some metal, you only need to replace one cutter instead of the entire blade. Also, because they have four sides, you can just turn them 90 degrees when they get dull. This allows them to last much longer than classic straight knives.

Helical Heads are also better at dealing with difficult grain and generally give better results. We would still recommend the upgrade, because as mentioned before, there are so many advantages to helical cutterheads.

The price difference, even if pretty high in percentage terms, in absolute terms is quite small, especially compared to other machines where it can cost times as much to upgrade to a helical head.

Combined with potential cost savings of less frequent replacements, the difference becomes even smaller. This makes the upgrade well worth it in our opinion. JET also makes two 8-inch jointers, which again are identical except for the style of the cutterhead.

Unlike the standard 6-inch model, the 8-inch standard model does not have quick-change knives. This means you will have to set up the knives in the classic way every time you change them. The two 8-inch models are very similar to the 6-inch ones and have all the same features. The only design difference is that the handwheels to raise and lower the tables are located underneath rather than on the front.

The 8-inch models have a more powerful 2 HP motor and longer vs mm and wider tables than their smaller siblings. To read a detailed description of all features and components of the 8-inch jointers, jet 6 inch jointer planer queue up to the introduction of the 6-inch models. This is a relatively time-consuming and to some annoying task, which needs to be repeated each time the blades are taken out to be sharpened or replaced.

It is a bit strange that JET offers the quick-change system which we think is a major upgrade on their standard 6-inch model, but not on the standard 8-inch jointer. Maybe they will add it in the future, but currently it is not available. The fact that the standard model has standard knives and not quick-change ones makes the upgrade to helical head cutters even more of an upgrade.

In percentage terms this is about the same upgrade cost jet 6 inch jointer planer queue for the 6-inch jointers.

Even though it is more expensive, the upgrade is so significant that we would strongly recommend it. Because of all the time and energy saved from setting up the blades it will be worth it in the long run.

Add to that the lower costs and all the advantages and it seems like a no-brainer to get the helical head model unless your budget is really tight. Knowing the jet 6 inch jointer planer queue between the four models, you may wonder whether you should get the 6 or 8-inch jointer.

Which one is right for you depends on multiple things, but in most cases we jet 6 inch jointer planer queue the 8-inch jointer is the way to go. Size is the key word here. When you want to make a table top or any large surface you will probably be handling boards wider than 6 inches. This is a major downside to the 6-inch models, because you will have to rip the jet 6 inch jointer planer queue down to less than 6 inches, and then glue them back together.

If you have many boards to process, the work really piles up. It is not a question of compactness, because in terms of width, an 8 or even inch jointer would not be much larger than a 6-inch one. One thing that may help to work with the limited width of these jointers is to let your lumber supplier already rip boards to a size that fits on your machine. This will save you time and energy having to resize wider boards.

TIP: If you want to find a good deal for any of these jointerskeep an eye on our price tracker. We track machine Jet Jointer Planers 5g prices for multiple different stores and update them on our site daily. We hope you find this guide helpful! Which model would you go with? Let us know in the comments below. JET 8-inch Jointers Should you get a 6 or 8-inch jointer or even bigger? Only need to set up blades once and are easy to change.

Long tables, solid fence. Easy to replace blades, quieter, better jointing results, and blades last longer. Blades cannot be resharpened, if damaged the whole blade needs to be replaced.

Limited width and power. More expensive. See all Prices. Pork Chop Guard. Front-mounted Handwheel. Extra long tables. Designed in United States. Manufacturer JET. Production status New. User rating 1.

May 09,  · About Press Copyright Contact us Creators Advertise Developers Terms Privacy Policy & Safety How YouTube works Test new features Press Copyright Contact us Creators.

Router Table Attachment For Delta Table Saw Method Do It Yourself Wood Ornaments Quotes