Thread nut on to table stop bolt Fig. If there are questions or comments, please contact your local supplier or JET. Restore password. Loosen two lock knobs Fig. Refer to Figure The smaller the gauge number, the heavier the cord. Works as expected so far.

Page 4: Table Of Contents Page 5: About This Manual Additional knowledge can be obtained from experienced users or trade articles. Whatever accepted methods are used, always make personal safety a priority. If there are questions or comments, please contact your local supplier or JET. JET can also be reached at our web site: www.

Page 6: Specifications 4. Page 8: Setup And Assembly Read and understand the entire contents of this manual before attempting assembly or operation. Failure to comply may cause serious injury. Figure hardware package Box 1: Stand not shown 5.

Only hand tighten screws at this time. Figure 5. Take measurements at both front and back of table — these should be identical. If miter slot is not parallel to blade, bump table with rubber mallet in the needed direction. Page Storage Screw Improper connection of the equipment-grounding conductor can result in a risk of electric shock.

The conductor with insulation having an outer surface that is green with or without yellow stripes is the equipment-grounding conductor. Page Voltage Conversion Zero setting of cursor cannot be used with horizontal fence position. Figure 6. Remove dust block C, Figure Carefully remove blade from top wheel, then from between upper and lower blade guides and lower wheel. Slide blade out through slot in Jet 14 Deluxe Pro Bandsaw Manual Zip table. Guide new blade through table slot.

Place blade loosely in upper and lower blade guides. The blade performance. Tip: When the band saw is not being used, raise tension lever to release position — Page Upper Thrust Bearing 7. Refer to Figure The thrust bearing prevents backward deflection of blade during cutting.

Disconnect band saw from power source. Replacement Parts. Mortisers Grinders Scroll Saws Accessories. Stay Connected Be the first to know about new products, events and special offers. Roll over Image to Zoom.

Stock No. This product ships direct from the manufacturer: Your order will ship in business days. This product is considered special order. Your account will be charged when you place your order. Express or overnight shipping is not available for this product. Ships by Ground to the 48 contiguous states.

The saw gets five stars, but I do have some nits. Most importantly, it does not have a magnetic switch. If the power goes off while the saw is running, and then comes back on hours later, the saw starts up again. That's bad.

Thus, sawdust escapes from around the lower door even when a vacuum is applied. Finally, as many have pointed out, you have to buy a fence separately. At this price, these flaws should not be present. Overall, however, this is a fine, sturdy and precise saw. I'm looking forward to many years of productive use.

Shipping was a day later than planned thru Old Dominion. I called Woodcraft at end of promised delivery time to find status of delivery.

Woodcraft was very helpful in finding delivery had been sent out on wrong truck to another state. Day later delivery and the driver was helpful, all was intact and slid the boxes out of semi trailer onto my pickup. Backed up to shop and unloaded with hand dolly. Was able to assemble myself using ladder and come along to raise saw onto base. Have been cutting Box Elder into use for lathe and scroll saw. Works as expected so far. Need to purchase a fence soon.

This will be my last bandsaw. I did a ton of research before pulling the trigger on this baby, and after 1 year I'm still very happy. Does everything I ask it with quiet precision. This machine is powerful and quiet. I installed an excellent, non-Jet aftermarket fence from my older saw and this Jet cuts straight and true without drift. The built in 12" capacity is great - no riser block needed.

Guide bearings and tracking are easy to adjust with window on edge of upper door and this setup is well-described in the manual. There are angled stabilizing supports bolted to the back of the base to prevent tipping the motor is bolted to the back of the cast iron frame creating a bit of a top heavy machine.

Do this first! Very nice that there is a lever for quick release of band tension. This I found puzzling. The tech also told me that tensioning can be done with the release lever disengaged opposite of what is said in the manual; see below. Another downside to the tensioning process: the knob is obscenely small, but with a good bit of effort you can get the band up to the proper scale mark, but it is not something you would cherish doing every day.

Please note that a plastic scale was stuck with adhesive to the back of the block indicating where the level of tension needed to be for different size blades.

Easy Woodworking Gift Ideas 2020 Behlen Salad Bowl Finish Msds Youtube Diy Resin Knife Scales