The idea is to strip the door down to a single piece so you can work quickly and efficiently. Trim or scrape the factory sealant that has seeped out between window trim and the glass, if applicable. Soak up a small amount of mineral spirits with a clean cloth or sponge and scrub the entire surface of the door from top to bottom to prepare it to accept the new finish. Concentrate on wiping the gel coat stain fiberglass doors uk stain from the surface but allow the stain to accentuate the grain that is embossed in the fiberglass. Gel coat stain fiberglass doors uk you elect to stain rather than paint the outside of your door, follow steps We suggest using mineral spirits to clean up. Refinishing Kitchen Cabinet Ztain.

Mask off any glass and weather stripping that was unable to be removed as well as the doorjamb. Using one of your extra cleanup rags, wipe the entire surface with either the provided mineral spirits, or an all purpose cleaner. Wipe clean and allow to dry thoroughly. Stir the stain well. Obtain a feel for the staining process by picking a small, flat area on the door to practice. Apply stain liberally in this small area with the sponge brush and remove excess stain gradually until the depth of color is satisfactory.

When finished practicing, remove the stain in this test area with the provided mineral spirits and extra cleanup rags. Staining Sequence. Stain all door panels following the order indicated on this diagram. Raised panels and surrounding recessed areas Inside panels with a vertical grain Inside panels with a horizontal grain Outside panels with a vertical grain Outside edges of the door.

Apply Stain Stir the stain thoro- ughly to ensure color consistency. Remove Excess Stain With the cloth provided, remove excess stain from the coated area. Concentrate on wiping the excess stain from the surface Gel Coat Stain Fiberglass Doors Ltd but allow the stain to accentuate the grain that is embossed in the fiberglass. Step Three. Step Four. Protect with Polyurethane Wait at least eight hours and up to 24 hours or longer depending on drying conditions before topcoating the stained door.

Exterior Doors. Helpful Hints. We suggest using mineral spirits to clean up. However, some of these can be used with an undercoat. We welcome your comments and suggestions. All information is provided "AS IS. All rights reserved. You may freely link to this site, and use it for non-commercial use subject to our terms of use. View our Privacy Policy here. Toggle navigation subscribe. Types of Stain to Use for Fiberglass Doors.

Written by Doityourself Staff. To ensure our content is always up-to-date with current information, best practices, and professional advice, articles are routinely reviewed by industry experts with years of hands-on experience. Charles Ramos, Jr. Shorten a Door. Basics Painting. We recently had a wood grained Fiberglass door installed. Read More. Refinishing Kitchen Cabinet Doors. I am trying to understand how I can re-finish my 's arched cabinet door Delaminating Exterior Fiberglass Door.

The upper center portion of our fiberglass door has a bulge - the fiberglas If you're renewing a door that's been stained previously, it will be necessary to first get rid of the old finish. You can do this by slathering it with a thin coat of chemical solvent, which will slowly liquefy the dried stain. Let the solvent sit for minutes, then wipe away all traces of chemical residue using a disposable rag. Before you begin stripping the door, check the manufacturer's guidelines by visiting their website or calling their customer service line to find out which products they recommend.

Part 2 of Select a gel stain in the desired color. Unlike wood and other materials, fiberglass surfaces should always be stained with oil-based gel products. Gel stains are thicker and creamier than other types of stains, which makes them better able to adhere to smooth synthetic materials and gives them a bold, uniform appearance. Gel stains are available in a variety of shades. This will allow you to simulate the look of different types of wood. Apply a liberal amount of stain to the inner panels of the door.

Slather on the stain using a 2 in 5. Start with the raised and recessed sections at the center of the door. Be sure to work the stain deep into the imitation grain pattern or any other textural detailing. Not only will they keep your hands clean, they'll also keep you from transferring the oils on your skin to the door. Stir the stain thoroughly before you begin to ensure that it goes on with a consistent texture. Remove excess stain using a clean rag.

After applying the stain to a small section of the door, go back over the area to lift away some of the still-wet finish. You'll notice the color gradually becoming lighter. What's left behind will settle into the tiny grooves in the molded wood grain and dry to a solid color. Continue brushing and wiping until you achieve the desired shade. The finish will take on a slightly darker tone with each application.

It may take several coats before you get your door looking the way you want it. For the most consistent finish, stain the entire door and Gel Coat Stain Fiberglass Doors Video apply follow-up coats as needed rather than concentrating on a single section at a time. Most gel stain manufacturers recommended using a total of no more than 2 or 3 coats. Applying the stain too thick may hinder its ability to dry fully.

Work your way to the outer portions of the door. When you're done staining the interior panels, move on to the outlying areas, including the surrounding grooves and the flat sections at the top, bottom, and sides. Save the outermost edges of the door the parts that rest against the jamb when closed for last.

Let the stain dry for hours. Most gel stains take about half a day to dry completely. However, exact drying times will vary depending on the amount of stain you use, the size of the door being finished, and specific environmental conditions.

Perform a touch test on an inconspicuous part of the door sometime after the first 24 hours. If it feels tacky, it needs a little longer. Don't forget to stain the opposite side of the door once the first side is dry. Part 3 of Apply a final protective clear coat. Once the door is completely dry, brush on a layer of liquid polyurethane or a similar water-based sealant. Apply the clear coat the same way you did the stain, starting with the inside panels and working your way out, finishing with the edges.

If you're staining an exterior door, select an outdoor varnish that will hold up to regular exposure to sunlight, Gel Coat Stain Fiberglass Doors Korea precipitation, and extreme temperatures. Allow the clear coat to dry for 8 to 24 hours. It's a good idea to leave the door to dry overnight, just to be on the safe side.

Wood Serving Tray Plan Learning Slimline Pen Hardware Kit Youtube Craftsman Radial Arm Saw 63503 Quick Toggle Clamps Home Depot 365