Top-Mount Refrigerator. Close Start Chat. Craftsman radial arm saw repair and replacement parts Craftsman radial arm saws use powerful drive motors and top-quality blades to give you the cutting performance that you expect. See Figure 23B. This manual is also suitable for: - professional laser 10 in. Every radial arm saw is designed for speed and flexibility.

Current Offers. New Arrivals. User Ratings. Minimum Rating. How's your shopping experience on this page? Quality cuts are easy with a radial arm saw from Sears Professional contractors and do-it-yourself experts know the importance of consistent board cuts when tackling a woodworking project.

Google Adsense. Speed control. The speed control regulates blade speed so the cutting blade spins at the appropriate speed to cut the work piece. Drive motor. The drive motor spins to drive the cutting blade to cut through the work piece. Work area safety guidelines to follow when using your Craftsman radial arm saw Work in a well-lit area so Craftsman Radial Arm Saw 63503 Ubuntu you can clearly see the work piece and the location of the saw blade.

Make sure that your work area is well-ventilated. Don't operate your radial arm saw in the presence of flammable liquids, gases or dust. Keep children and bystanders away from the work area when operating the saw. Distractions can cause you to lose control of the radial arm saw.

Wear work gloves to protect your hands and eye protection when using the radial arm saw. LG Dishwasher Parts. Food Processor.

Kitchenaid Food Processor Parts. Outdoor Grill. Outdoor Grill Parts Kenmore elite. Craftsman Planer Parts. Range Parts GE. Page 23 4 Iockwashers 5t16 in. Page 24 [] Pick up the yoke assembly and carefully slip it onto the carriage track below the arm. Keep it parallel with the arm so bearings slide in smoothly. There are holes in both sides of each support. The long side of each support with the slotted holes fits against the saw base. The yoke clamp keeps the yoke from rotating on the carriage when you want the saw blade to be station- ary.

Use this procedure to check and set the yoke clamp. Page 28 [] Replace the rear cover and rear cover screws. The purpose of this procedure is to check whether the inner coJumn tube is snug in the housing and to remove any looseness.

Page 29 [] Rotation Check: To check the rotation, hold the front of the arm with one hand and grasp the top of the column support with the other. Press the arm to the side.

Page 30 Loose carriage bearings permit the blade to wander slightly while cutting, which will result in a poor cut and more wear and tear on the saw. Use the following steps to check for tightness and Craftsman Radial Arm Saw 63503 Ups to then adjust the bearings if needed.

Page 31 [] Move the arm to the opposite side and repeat the above procedure. When the opposite side is level, recheck the first side to make sure that it is still accurate and even. Page 32 [] Snap the U-clip onto the front edge of the saw base.

Line up the hole in the U-cfip with the saw base hole just to the left of the center Craftsman Radial Arm Saw 63503 Video notch in saw base. See Figure 23B. Page 33 [] Tighten the thumbscrews to clamp the table sec- tions into place.

Page 34 See Figures 26A - 26C. Place the inner blade washer, saw blade, outer blade Craftsman Radial Arm Saw Rebuild Kit Github washer, and blade nut on the blade arbor. See Figure 26A. Note: The concave side of blade washers go against the blade. Page 35 [] Orient i nnerslotted metal s tripsothatit is located totheleftofouterslottedmetal s trip. Tighten retaining screwsecurely. Page 36 The control cut device offers many benefits.

As it increases operator control, it eliminates the risk in a cross cut of the saw "climbing" out and over the workpiece at the operator. Feed control of the blade as it cuts through the workpiece increases, as does the accuracy of the cut. Lock the yoke lock handle right side of saw, below yoke and the bevel lock lever. Page 38 Place the square flat against the blade between two teeth. If not, kickback could result during a cross cut. Kickback can cause serious injury by throw- ing the workpiece toward the operator.

In addi The rip scale indicators on the arm show the distance between the blade and the rip fence. The upper scale is used when the fence is positioned directly behind the front table, The lower scale is used when the fence is at the extreme rear, directly in front of the column. Page Labels The control cut device offers many benefits, As it increases operator control, it eliminates the risk in a cross cut of the saw "climbing" out and over the workpiece at the operator, Feed control of the blade as it cuts through the workpiece increases, as does It can make dado or molding cuts with special attachments, This saw is designed to cut wood and wood composi Page 45 The yellow switch key prevents accidental starting of the main power switch when saw is not being used.

To activate the switch, insert the switch key and lift switch to ON position. To lock the switch once it has been pressed to OFF, remove the yellow key. Refer to the drawings and instructions provided so you can make safer and more precise cuts. Turn the saw off with the switch on the arm but hold the handle until the blade stops rotating.

Let the blade build up to full speed before it contacts the wood. Once both lines are in alignment, do not move the Page 56 The laser is activated by means of a centrifugal switch only while the saw motor is running and the laser guide is mounted on the saw. After cleaning laser guide and replacing batteries, secure laser guide cover to laser guide support using Page 57 Rfthe power cords are worn, cut, or damaged in any way, have them replaced immediately by a qualified service technician at a Sears store or repair center.

Shank Router Cutter Education Bench Vises At Lowes Best Wood Burning Tools Quote Woodworking Belt Sander Reviews Data